Husqvarna 55 Starter device, Changing a broken or worn starter cord, Tensioning the recoil spring

Page 30

MAINTENANCE

Starter device

!WARNING!

•When the recoil spring is assembled in the starter housing, it is in tensioned position and can when treated carelessly, pop out and cause injuries.

•Always be careful, when changing the recoil spring or the starter cord. Always wear safety goggles for eye protection.

Changing a broken or worn starter cord

•Loosen the screws, that

hold the starter device against the crankcase and remove the starter device.

•Pull out the cord approx. 30 cm and lift it up into the notch in the pulley. Zero-set

the recoil spring by letting the pulley rotate slowly backwards. Undo the screw in the centre of the pulley and remove the pulley.

•Insert and fasten a new

starter cord in the pulley. Wind approx. 3 turns of the starter cord on to the pulley. Assemble the starter pulley against the recoil spring, so the end of the spring engages to the pulley. Fit the screw in the centre of the pulley. Carry the starter cord through the hole in the starter housing and the starter handle. Make a knot on the starter cord.

Tensioning the recoil spring

•Lift the starter cord up in the notch on the starter pulley and turn the starter pulley 2 turns clockwise.

NOTE! Check that the starter pulley can be turned at least half a turn, when the starter cord is entirely pulled out.

Changing the broken recoil spring

•Lift the starter pulley (see "Changing a broken or worn

starter cord").

•The recoil spring is disassembled from the

starter device, with its inside facing down. Tap the starter lightly against a working bench or similar. If the spring pops out when assembling, it should be mounted again, out and in towards the centre.

•Lubricate the recoil spring with thin oil. Assemble the

starter pulley, and tension the recoil spring.

Starter device assembly

•Assemble the starter device, by pulling the starter cord out first, then place the starter against the crankcase. Then slowly release the starter cord so

that the pulley engages with the pawls.

• Assemble and tighten the screws, which hold the starter.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Operators manual EPA KEY to Symbols SymbolsContents Safety Instructions Chain SAW Safety EquipmentPersonal Protective Equipment Chain brake and front hand guard 3a StartingThrottle lock Chain catcherRight hand guard Stop switch Vibration damping systemMuffler Checking the inertia brake release Checking brake band wearChecking the front hand guard Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesSaw chain Cutting equipment designed to minimise kickbackBar Some terms that describe the bar and chainSharpening cutting teeth Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Risk of kickback is increased with a badly sharpened chainGeneral advice on setting raker clearance Setting the raker clearanceTensioning the chain Filling with chain oil Lubricating cutting equipmentChain oil Never use waste oilLubricating the bar tip sprocket Checking chain lubrication Needle bearing maintenanceChecking wear on cutting equipment Chain drive sprocketHOW to Avoid Kickback What is kickback?General rules Do not let go of the handlesNever use the saw one- handed General Safety Precautions Min m10 ft Basic safety rules General Working InstructionsTerms Basic cutting techniqueGeneral CuttingLimbing Tree felling techniqueSafe distance Felling directionClearing the trunk and preparing your retreat FellingCutting the trunk into logs General adviceFreeing a tree that has fallen badly = high accident risk Freeing a Trapped treeWhat is WHAT? Assembly Mounting guide bar and chainFuel Handling FuelmixFuelling Min 3 m10ft Stop Start and StopStart Cold engineMaintenance CarburetorChanging a broken or worn starter cord Starter device assemblyStarter device Tensioning the recoil springMuffler Needle bearing maintenanceAir filter Spark plugTemperature -5C or colder Centrifugal cleaning Air InjectionTemperature 0C or colder Cooling systemWeekly maintenance Daily maintenance Monthly maintenanceTechnical Data Obligations Emission Control Warranty StatementYour Warranty Rights 487-5963114 01 2002W16

55 specifications

The Husqvarna 55 chainsaw is a robust and reliable tool that has earned its place among both professional loggers and amateur woodcutters. Designed for hard work, this powerful chainsaw boasts a mix of features and technologies that ensure efficiency, durability, and ease of use, making it an excellent choice for a variety of cutting tasks.

One of the standout features of the Husqvarna 55 is its powerful engine. The chainsaw is equipped with a 3.5 horsepower, 2-stroke petrol engine that generates strong power output, enabling it to tackle demanding cutting jobs effortlessly. The engine is coupled with an advanced air injection system that helps to reduce wear and tear, ensuring the longevity of the saw. This design minimizes the amount of dirt and debris that enters the air filter, thus extending the time between filter cleanings and enhancing performance.

Another key characteristic of the Husqvarna 55 is its weight balance and ergonomic design. Weighing approximately 4.2 kg, the saw is lightweight enough for long periods of use without causing significant fatigue. Furthermore, the design incorporates an anti-vibration system that significantly reduces vibrations felt by the user during operation, allowing for greater control and comfort.

The chainsaw showcases a rapid tensioning system, which allows for quick and effortless adjustment of the chain tension without any tools. This feature is particularly helpful for maintaining optimal chain performance and ensuring safety during operation. The Husqvarna 55 also comes equipped with a safety chain brake system that provides additional protection to the operator, reducing the risk of accidents.

In terms of cutting capacity, the Husqvarna 55 features a bar length of typically 16 inches, making it suitable for various applications, from felling small trees to pruning larger limbs. The combination of the engine power, smooth operation, and the quality of the cutting chain results in efficient, clean cuts.

The durability of the Husqvarna 55 is further enhanced with its sturdy construction, featuring a robust chassis that can withstand the rigors of heavy use. Overall, the Husqvarna 55 is an exceptional chainsaw that combines power, comfort, and safety, making it an outstanding investment for those who demand reliability in their cutting tools. Whether you're a seasoned professional or an enthusiastic hobbyist, the Husqvarna 55 is designed to meet your cutting needs with ease and efficiency.
Top Page Image Contents