Husqvarna 49 manual Tree felling technique, Safe distance, Limbing, Felling direction

Page 21

SAFETY INSTRUCTIONS

2 The log is supported at one end. There is a high risk that it will split.

AStart by cutting from below (about 1/3 of the way through).

BFinish by cutting from above so that the two cuts meet.

3Tree felling technique

!It takes a lot of experience to fell a tree. Inexperienced users of chain saws should not fell trees. NEVER ATTEMPT A TASK YOU ARE UNSURE OF.

A Safe distance

The safe distance between a tree that is to be felled and anyone else working nearby is at least 21/2 tree lengths. Make sure that no-one else is in this "risk zone" before or during felling.

3 The log is supported at both ends. There is a high risk that the chain will jam.

AStart by cutting from above (about 1/3 of the way through).

BFinish by cutting from below so that the two cuts meet.

Limbing

When limbing thick branches you should use the same approach as for cutting.

Cut difficult branches piece by piece.

1

2

 

 

3

B Felling direction

The aim is to fell the tree in the best possible position for subsequent limbing and cross-cutting. You want it to fall on ground where you can move about safely.

The main point to avoid is letting the tree fall onto another tree. It can be both difficult and dangerous to remove a tree in such a position (see point 4 in this section).

Once you have decided which way you want the tree to fall you must judge which way the tree would fall naturally.

Several factors affect this:

Lean of the tree

Bend

Wind direction

Arrangement of branches

Weight of snow

You may find you are forced to let the tree fall in its natural direction because it is impossible or dangerous to try to make it fall in the direction you first intended.

Another very important factor, which does not affect the felling direction but does affect your safety, is to make sure the tree has no damaged or dead branches that might break off and hit you during felling.

!During critical felling operations, hearing protectors should be lifted immediately when sawing is completed so that sounds and warning signals can be heard.

English – 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 101 90 45/49Symbols KEY to SymbolsContents Safety Instructions Chain SAW Safety EquipmentPersonal Protective Equipment Chain brake and front hand guard Throttle lock Chain catcherRight hand guard Stop switch Vibration damping systemMuffler Checking the front hand guard Checking brake band wearChecking the automatic brake Checking the brake triggerThrottle lock 5 basic rules Cutting EquipmentBar Cutting equipment designed to minimise kickbackSaw chain Some terms that describe the bar and chainSharpening your chain and adjusting raker clearance General information on sharpening cutting teethSharpening cutting teeth General advice on setting raker clearance Setting the raker clearanceTensioning the chain Lubricating cutting equipment Chain oilFilling with chain oil Lubricating the clutch drum bearing Checking chain lubricationChecking wear on cutting equipment Lubricating the bar tip sprocketWhat is kickback? HOW to Avoid KickbackDo not let go of the handles General rulesGeneral Safety Precautions Min m10 ft General Working Instructions Basic safety rulesGeneral Basic cutting techniqueTerms CuttingSafe distance Tree felling techniqueLimbing Felling directionFelling Clearing the trunk and preparing your retreatCutting the trunk into logs Freeing a tree that has fallen badly = high accident riskFreeing a Trapped tree Cutting trees and branches that are in tension PreparationsWhat is WHAT? Mounting guide bar and chain AssemblyFuelmix Fuel HandlingFuelling Min 3 m10ft Cold engine Start and StopWarm engine StartCarburetor MaintenanceStarter device Starter device assemblyChanging a broken or worn starter cord Tensioning the recoil springAir filter Needle bearing maintenanceMuffler Spark plugDaily maintenance Centrifugal cleaning Air InjectionCooling system Weekly maintenance Monthly maintenance Technical Data Your Warranty Rights Obligations Federal Emission Control Warranty Statement1998W48
Top Page Image Contents