Husqvarna 455e, 455, 460 manual Throttle lockout, Chain catcher, Right hand guard

Page 9

GENERAL SAFETY PRECAUTIONS

In the felling position the left hand is in a position that makes manual activation of the chain brake impossible. With this type of grip, that is when the left hand is placed so that it cannot affect the movement of the front hand guard, the chain brake can only be activated by the inertia action.

Will my hand always activate the chain brake during a kickback?

No. It takes a certain force to move the hand guard forward. If your hand only lightly touches the front guard or slips over it, the force may not be enough to trigger the chain brake. You should also maintain a firm grip of the chain saw handles while working. If you do and experience a kickback, your hand may never leave the front handle and will not activate the chain brake, or the chain brake will only activate after the saw has swung around a considerable distance. In such instances, the chain brake might not have enough time to stop the saw chain before it touches you.

There are also certain positions in which your hand cannot reach the front hand guard to activate the chain brake; for example, when the saw chain is held in felling position.

Will my inetria activated chain brake always activate during kickback in the event of a kickback?

No. First your brake must be in working order. Testing the brake is simple, see instructions under the heading Checking, maintaining and servicing chain saw safety equipment. We recommend you do before you begin each work session. Second the kickback must be strong enough to activate the chain brake. If the chain brake is too sensitive it would activate all the time which would be a nuisance.

Will my chain brake always protect me from injury in the event of a kickback?

No. First, the chain brake must be in working order to provide the intended protection. Second, it must be activated during the kickback as described above to stop the saw chain. Third, the chain brake may be activated but if the bar is to close to you the brake might not have enough time to slow down and stop the chain before the chain saw hits you.

Only you and proper working technique can eliminate kickback and its danger.

Throttle lockout

The throttle lockout is designed to prevent accidental operation of the throttle control. When you press the lock (A) (i.e. when you grasp the handle) it releases the throttle control

(B). When you release the handle the throttle control and the throttle lockout both move back to their original positions. This arrangement means that the throttle control is automatically locked at the idle setting.

Chain catcher

The chain catcher is designed to catch the chain if it snaps or jumps off. This should not happen if the chain is properly tensioned (see instructions under the heading Assembly) and if the bar and chain are properly serviced and maintained (see instructions under the heading General working instructions).

Right hand guard

Apart from protecting your hand if the chain jumps or snaps, the right hand guard stops branches and twigs from interfering with your grip on the rear handle.

English – 9

Image 9
Contents 455e Rancher KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Throttle lockout Chain catcherRight hand guard Cutting equipment Stop switchVibration damping system MufflerCutting equipment designed to reduce kickback General rulesBar ChainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethSharpening cutting teeth Adjustment of depth gauge setting General advice on adjusting depth gauge settingTensioning the chain Rancher455e Rancher Lubricating cutting equipmentChain oil Filling with chain oilChain drive sprocket Checking chain lubricationNeedle bearing lubrication Checking wear on cutting equipmentBar Fitting the bar and chain AssemblyRancher 455e RancherFitting a spike bumper Fuel Fuel HandlingFuelling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsAlways use a fast cutting speed, i.e. full throttle Basic cutting technique GeneralTerms Cutting LimbingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburettor adjustmentGeneral High speed jet H Correctly adjusted carburettorChecking brake band wear Checking the front hand guardChecking the brake trigger Muffler StarterChanging a broken or worn starter cord Tensioning the recoil spring Air filterChanging a broken recoil spring Fitting the starterSpark plug Adjustment of the oil pumpLubricating the bar tip sprocket Needle bearing lubricationTemperature 0C or colder Air Injection centrifugal cleaningTemperature -5C or colder Cooling systemDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsApplies to Europe only EC-declaration of conformity´z+R9¶6x¨ Page 1150250-26 ´z+R9¶6x¨ ´z+R9¶6x¨