Husqvarna 61, 268, 272XP manual General Working Instructions, Basic safety rules

Page 19

SAFETY INSTRUCTIONS

GENERAL WORKING INSTRUCTIONS

This section describes basic safety rules for using a chain saw. This information is no substitute for professional skills and experience. If you get into a situation where you feel unsafe, stop and seek expert advice (look under FORESTRY SERVICES in the telephone directory).

DO NOT ATTEMPT ANY TASK THAT YOU FEEL UNSURE OF!

Important

1 Before using a chain saw you must understand the effects of kickback and what causes it. (See the section on ”How to avoid kickback”.)

2 Before using a saw you must understand the difference between sawing with the top and bottom edges of the bar. (See the section on ”How to avoid kickback”.)

1 Basic safety rules

1 Look around you:

•to make sure there are no people, animals or other

objects nearby that might affect your work.

• to make sure that none of the above might come within reach of your saw or be injured by falling trees.

Follow the instructions above, but do not use a chain saw in a situation where you cannot call for help in case of an accident.

4Check the area around you for possible obstacles such as roots, rocks, branches, ditches, etc., in case you have to move suddenly. Take great care when working on sloping ground.

5Take the utmost care when cutting through branches or logs that are in tension. A log or branch that is in tension can suddenly spring back into its natural position before or after you cut it. If you stand on the wrong side or start cutting in the wrong place it may strike you or your chain saw. This could make you lose control and cause a serious accident.

6Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the saw with the bar and chain pointing backwards. Fit a guard to the bar before carrying the saw any distance.

2Do not use the saw in bad weather, such as dense fog, heavy rain, strong wind, intense cold, etc. Working in cold weather is tiring and often brings added risks, such as icy ground, unpredictable felling direction, etc.

3Take great care when removing small branches and avoid cutting bushes (i.e. cutting many small branches at the same time). Small branches can be grabbed by the chain and thrown back at you, causing serious injury.

7Never put a chain saw down while the engine is running unless you have it in clear view and the chain brake is on. Switch the engine off before leaving your chain saw for any length of time.

English – 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 101 91 61/268/272XPSymbols on the chain saw KEY to SymbolsSymbols in the operator’s manual Contents Personal Protective Equipment Safety InstructionsChain brake and front hand guard Chain catcher Throttle lockRight hand guard Vibration damping system Stop switchMuffler Checking the brake trigger Checking brake band wearChecking the front hand guard Checking the inertia brake releaseThrottle lock 5 basic rules Cutting EquipmentSome terms that describe the bar and chain Cutting equipment designed to minimise kickbackBar Saw chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth Setting the raker clearance General advice on setting raker clearanceTensioning the chain Chain oil Lubricating cutting equipmentFilling with chain oil Lubricating the bar tip sprocket Checking chain lubricationLubricating the clutch drum bearing Checking wear on cutting equipmentWhat is kickback? HOW to Avoid KickbackDo not let go of the handles General rules10 ft Min mGeneral Working Instructions Basic safety rulesCutting Basic cutting techniqueGeneral TermsFelling direction Tree felling techniqueSafe distance LimbingFelling Clearing the trunk and preparing your retreatCutting trees and branches that are in tension Preparations Freeing a tree that has fallen badly = high accident riskCutting the trunk into logs Freeing a Trapped treeWhat is WHAT? Mounting guide bar and chain AssemblyFitting a spike bumper Fuelmix Fuel HandlingMin 3 m Fuelling10ft Warm engine Start and StopStart Cold engineCarburettor MaintenanceTensioning the recoil spring Starter device assemblyStarter device Changing a broken or worn starter cordMuffler Adjusting the oil pumpAir filter Spark plugCooling system Needle bearing maintenance Winter useTemperature 0oC 32oF or colder Temperature -5oC 23oF or colderMonthly maintenance Weekly maintenance Daily maintenance268 Technical DataBar and chain combinations 272XP EU declaration of conformity Only applies to Europe English 38´*33¶6\¨ English ´*33¶6\¨
Top Page Image Contents