Note:
When listening to an FM station, fully extend the antenna to insure maximum reception.
Automatic tuning relies on the signal strength of the broadcasting station. Weaker stations are often skipped when using automatic tuning. Manual tuning is suggested for locating and programming weaker stations and also for fine tuning stations found during automatic scan.
For FM stereo reception, the unit provides FM MONO/STEREO selection. In stereo mode, the unit will automatically switch to stereo when a FM stereo broadcast is received and the Stereo indicator (#D15) will light.
To receive a weak (noisy) FM station, press the ST/MO Button (H5) to switch to MONO mode. The reception may be improved, but the sound is monaural (MONO).
TOPRESETCHANNELS
This unit is equipped with 20 preset memories for bothAM and FM 
1.Press the
Button (10/H1) to turn on the unit. 2.Press the Function Button (3/H3) to operate the unit in radio mode and desired band. 3.Tune to a desired station. 4.Press the MEMORY Button (7/H6), “MEMORY” (#D11) & number of pre
set station appears. 5.Press the MEMO + Button (6/H12) to select the desired preset channel.
6.Press MEMORY Button (7/H6) again to complete. 7.Tune to another station and repeat steps 4 to 6 to store the station in
another preset channel.
TO RECEIVE PRESET STATIONS
1.Press the 
Button (10/H1) to turn on the unit.
2.Press the Function Button (3/H3) to operate the unit in radio mode.
3.Press the MEMO + Button (6/H12) to select the preset channels.
AUX OPERATION
You can connect left and right audio outputs from a TV, VCR, DVD, MP3 player or other portable device to theAUX IN Jacks (21) on the rear of the system. To use this Front Loading Dual CD System to amplify your input audio signal:
1.Press the Function Button (3/H3) to operate the unit inAUX mode. “AUX” Indicator (#D5) appears in the display.
2.Turn on and start playing the device that is plugged into the AUX Jack.
3.Adjust the Volume Control to obtain the desired sound level.
PRESET EQ (EQUALIZATION SYSTEM)
The sound equalization can be adjusted for optimum sound reproduction depending on style of music you are playing. By pressing the EQ Button (14/H13), you can switch between FLAT, CLASS ROCK, POP .
USING HEADPHONES (NOT INCLUDED)
Inserting the plug of your headphones into the Headphone Jack (16) will enable you to listen in private. When using headphones, the speakers will be disconnected.
NOTE: READ THIS IMPORTANT INFORMATION BEFORE USING YOUR HEADPHONES
1.Avoid extended play at very high volume as it may impair your hearing.
2.If you experience ringing in your ears, reduce the volume or shut off your unit.
3.Keep the volume at a reasonable level even if your headset is an
SLEEP OPERATIONS
1.When the unit in ON, press the TIMER/SLEEP Button (13) to program the sleep time, SLEEP indicator will appears and 90 wil blinks on display.
2.Press 
& 
button (9/H11) to select the sleep time between
3.The display shows the chosen sleeping time momentarily and then returns to the current function mode. 4.The unit will automatically turn off after the set time has elapsed.
5.To cancel the Sleep operation, press the SLEEP Button (13) again until SLEEP indicator disappear or simply switch the unit to standby.
TIMER OPERATIONS
Your unit can be set to turn on at predetermined time in Radio/CD function mode for running 60 minutes unless turn off the unit manually. This setting can only be done in standby mode. To set the TIMER as follows : 1.PresstheTIMER/SLEEPButton (13/H14) once the ‘TIMER’ icon appear and the hour digit will blink to set the
timer on time during standby mode in the display.
2.Press the 
/ 
Button (11/H7) to adjust the hour.
3.Press the TIMER/SLEEP Button to (13/H14) confirm hour setting, minute position flashes.
4.Press the 
/ 
Button (11/H7) to adjust the minute.
5.Press the TIMER SLEEP Button (13/H14) to complete setting. The ‘TU’blinks and volume level will show.
6.Press the 
/ 
button (11/H7) to select the turn on function on volume level, press TIMER/SLEEP (13/ H14)button again to store the timer on function and the volume level will blink.
7.Press the 
/ 
button (11/H7) to select the volume level, press TIMER/SLEEP button (13/H14) again to complete timer setting, the ‘TIMER’ icon and current time will appear on display, the unit will turn on running 60 minutes once reach the time you set.
8 |
| 7/20/2005, 2:55 PM | |
|