Husqvarna 1151322-95 manual How to avoid kickback, Freeing a tree that has fallen badly

Page 27

WORKING TECHNIQUES

Freeing a tree that has fallen badly

Freeing a ”trapped tree”

It is very dangerous to remove a trapped tree and there is high accident risk.

Never try to fell the tree that is trapped.

Never work in the risk zone of the hanging trapped tree.

The safest method is to use a winch.

Tractor-mounted

Portable

Cutting trees and branches that are in tension

Preparations: Work out which side is in tension and where the point of maximum tension is (i.e. where it would break if it was bent even more).

Decide which is the safest way to release the tension and whether you are able to do it safely. In complicated situations the only safe method is to put aside your chain saw and use a winch.

General advice:

Position yourself so that you will be clear of the tree or branch when the tension is released.

Make one or more cuts at or near the point of maximum tension. Make as many cuts of sufficient depth as

necessary to reduce the tension and make the tree or branch break at the point of maximum tension.

Never cut straight through a tree or branch that is in tension!

If you must cut across tree/limb, make two to three cuts, one inch apart, one to two inches deep.

Continue to cut deeper until tree/limb bends and tension is released.

Cut tree/limb from outside the bend, after tension has been released.

How to avoid kickback

WARNING! Kickback can happen very

! suddenly and violently; kicking the chain saw, bar and chain back at the user. If this happens when the chain is moving it can cause very serious, even fatal injuries. It is vital you understand what causes kickback and that you can avoid it by taking care and using the right working technique.

What is kickback?

The word kickback is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the tip of the bar, known as the kickback zone, touches an object.

Kickback always occurs in the cutting plane of the bar. Normally the chain saw and bar are thrown backwards and upwards towards the user. However, the chain saw may move in a different direction depending on the way it

English 27

Image 27
Contents English 365 372XPYou will find the following labels on your chain saw KEY to SymbolsSymbols on the machine Symbols in the operator’s manualContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerCutting equipment designed to reduce kickback BarChain General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Lubricating cutting equipment Filling with chain oilChecking chain lubrication Chain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chainWorking with the chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueSafe distance Tree felling techniqueLimbing Log is supported at one end. There is a high riskFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cut How to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking the front hand guard Correctly adjusted carburetorHigh speed jet H Checking brake band wearImmediately Checking the inertia brake releaseMuffler Starter Changing a broken or worn starter cordTensioning the recoil spring Must always be replaced Air filterChanging a broken recoil spring Fitting the starterLubricating the bar tip sprocket Adjustment of the oil pumpWhen making adjustments Spark plugWinter use Air Injection centrifugal cleaningTemperature -5C 23F or colder Cooling systemElectrical carburetor heating CanadaOther countries Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Your Warranty Rights and Obligations Federal Emission Control Warranty StatementKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw Other safety precautionsPage 1151322-95