Husqvarna 1151002-95 manual Sharpening your chain and adjusting depth gauge setting

Page 12

GENERAL SAFETY PRECAUTIONS

•Number of drive links.

Sharpening your chain and adjusting depth gauge setting

General information on sharpening cutting teeth

•Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar through the wood and the chips will be very small. If the chain is very blunt it will produce wood powder and no chips or shavings.

•A sharp chain eats its way through the wood and produces long, thick chips or shavings.

•The cutting part of the chain is called the cutter and consists of a cutting tooth (A) and the depth gauge

(B). The cutters cutting depth is determined by the difference in height between the two (depth gauge setting).

When you sharpen a cutting tooth there are four important factors to remember.

1 Filing angle

2Cutting angle

3File position

4 Round ﬁle diameter

It is very difﬁcult to sharpen a chain correctly without the right equipment. We recommend that you use our ﬁle gauge. This will help you obtain the maximum kickback reduction and cutting performance from your chain.

See instructions under the heading Technical data for information about sharpening your chain.

WARNING! Departure from the

! sharpening instructions considerably

increases the risk of kickback.

Sharpening cutting teeth

To sharpen cutting teeth you will need a round ﬁle and a ﬁle gauge. See instructions under the heading Technical data for information on the size of ﬁle and gauge that are recommended for the chain ﬁtted to your chain saw.

•Check that the chain is correctly tensioned. A slack chain will move sideways, making it more difﬁcult to sharpen correctly.

•Always ﬁle cutting teeth from the inside face. Reduce the pressure on the return stroke. File all the teeth on one side ﬁrst, then turn the chain saw and ﬁle the teeth on the other side.

12 – English

Image 12

Contents Operator’s manual EPA II 576 XP EPA KEY to Symbols Symbols on the machineSymbols in the operator’s manual You will ﬁnd the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?576XP NE 570 General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Stop switch Cutting equipmentVibration damping system MufﬂerCutting equipment designed to reduce kickback BarChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Filling with chain oilChecking chain lubrication Chain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chainWorking with the chain Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Correctly adjusted carburetor High speed jet HChecking brake band wear Checking the front hand guardChecking the inertia brake release ImmediatelyMufﬂer Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAir ﬁlter Spark plugLubricating the bar tip sprocket Must always be replacedAdjustment of the oil pump Air Injection centrifugal cleaningWhen making adjustments Needle bearing lubricationWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain ﬁling and ﬁle gauges Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions´z+SÆ=¶52¨ Page Warranty Statement 1151002-95