Husqvarna 1151002-95 manual Maintenance schedule

Page 37

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section.

	Daily maintenance	Weekly maintenance	Monthly maintenance

		On chain saws without a catalytic	Check the brake band on the chain
		On chain saws without a catalytic	brake for wear. Replace when less than
	Clean the outside of the machine.	converter, check the cooling system	brake for wear. Replace when less than
	Clean the outside of the machine.	converter, check the cooling system	0.024 inch (0.6 mm) remains at the most
		weekly.	0.024 inch (0.6 mm) remains at the most
		weekly.	worn point.
			worn point.

	Check that the components of the	Check the starter, starter cord and	Check the clutch centre, clutch drum
	throttle control work safely. (Throttle	Check the starter, starter cord and	Check the clutch centre, clutch drum
	throttle control work safely. (Throttle	return spring.	and clutch spring for wear.
	lockout and throttle control.)	return spring.	and clutch spring for wear.
	lockout and throttle control.)

	Clean the chain brake and check that
	it operates safely. Make sure that the	Check that the vibration damping	Clean the spark plug. Check that the
	chain catcher is undamaged, and	elements are not damaged.	electrode gap is 0.020 inch (0.5 mm).
	replace it if necessary.

	The bar should be turned daily for
	more even wear. Check the
	lubrication hole in the bar, to be sure	Lubricate the clutch drum bearing.	Clean the outside of the carburetor.
	it is not clogged. Clean the bar	Lubricate the clutch drum bearing.	Clean the outside of the carburetor.
	it is not clogged. Clean the bar
	groove. If the bar has a sprocket tip,
	this should be lubricated.

	Check that the bar and chain are	File off any burrs from the edges of	Check fuel hose for cracks or other
	getting sufﬁcient oil.	the bar.	damage. Change if necessary.

	Check the saw chain with regard to
	visible cracks in the rivets and links,
	whether the saw chain is stiff or	Clean or replace the spark arrestor	Empty the fuel tank and clean the inside.
	whether the rivets and links are	screen on the mufﬂer.	Empty the fuel tank and clean the inside.
	whether the rivets and links are	screen on the mufﬂer.
	abnormally worn. Replace if
	necessary.

	Sharpen the chain and check its
	tension and condition. Check the	Clean the carburetor compartment.	Empty the oil tank and clean the inside.
	drive sprocket for excessive wear	Clean the carburetor compartment.	Empty the oil tank and clean the inside.
	drive sprocket for excessive wear
	and replace if necessary.

	Clean the starter units air intake.	Clean the air ﬁlter. Replace if	Check all cables and connections.
	Clean the starter units air intake.	necessary.	Check all cables and connections.
		necessary.

	Check that nuts and screws are tight.

	Check that the stop switch works
	correctly.

	Check that there are no fuel leaks
	from the engine, tank or fuel lines.

	On chain saws with a catalytic
	converter, check the cooling system
	daily.

English – 37

Image 37

Contents Operator’s manual EPA II 576 XP EPA Symbols on the machine KEY to SymbolsSymbols in the operator’s manual You will ﬁnd the following labels on your chain sawContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?576XP NE 570 Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Cutting equipment Stop switchVibration damping system MufﬂerBar Cutting equipment designed to reduce kickbackChain General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Filling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueLimbing Safe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatFelling cut Directional cutsFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburetorChecking brake band wear Checking the front hand guardImmediately Checking the inertia brake releaseMufﬂer Changing a broken or worn starter cord StarterTensioning the recoil spring Changing a broken recoil springSpark plug Air ﬁlterLubricating the bar tip sprocket Must always be replacedAir Injection centrifugal cleaning Adjustment of the oil pumpWhen making adjustments Needle bearing lubricationHeated handles Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain ﬁling and ﬁle gauges Your Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautions´z+SÆ=¶52¨ Page Warranty Statement 1151002-95