Husqvarna 180BF, 150BF, 115 09 83-95 manual Operation

Page 17
Operation

Operation

„ CONTROL ARM [150BF/170BF/180BF]

• Hold the upper end of the control arm in hand and, while pulling it away from the unit, rotate arm forward (counter-clockwise in the direction of the arrow) until it clicks. (The first position)

And if you want, you can rotate arm further until it clicks. (The second position)

Choose the arm position according to your working condition.

• To fold the arm, reverse the order.

(1)First position (2)Second position

„STARTING ENGINE

Manual background IMPORTANT

Avoid operating the blower with the flexible tube and swivel joint disconnected. That will reduce the cooling air and the engine could be damaged by overheating.

1.Push the primer bulb until fuel flows out in the clear tube.

2.When the engine is cool, close the choke.

(1)Choke Lever (2)Primer Bulb (3)OPEN (4)CLOSE

3. Set the throttle lever position.

[130BT]

[150BT/BF] [170BT/BF] [180BT/BF]

Idling

About 1/3 Open

(1)Full Throttle (2)About 1/3 Open (3)Idling

(4)STOP [130BT/150BT/170BT/180BT] as shown in F19 (5)Stop Switch [150BF/170BF/180BF] as shown in F20

4.To start, hold the top of the blower firmly with your left hand. Pull the starter knob slowly until you feel it engage and then give it a vigorous strong pull.

Manual background IMPORTANT

Never twist the starter cord around your hand.

Avoid pulling the starter rope out to its full extent and allowing the starter rope to snap back. This will prevent premature damage to the starter.

Do not let a person stand near the blower or the exhaust port.

5.Once the engine is running, gradually open the choke if it was set closed, and let the engine run at idle speed for a minute to warm it up.

Manual backgroundNOTE

When the engine fails to start after several attempts due to overchoking, open the choke and repeat pulling the rope.

Manual backgroundWARNING

Air comes out as soon as the engine is started, even at idle speed.

 

 

English

F14

 

 

 

[150BF] [170BF] [180BF]

F15

 

 

 

(1)

 

 

(2)

 

 

[150BF] [170BF] [180BF]

F16

 

(1)

 

 

 

 

(4)

 

 

(3)

(2)

 

[130BT]

F17

 

(1)

 

 

 

 

(3)

 

 

(4)

 

(2)

[150BT/BF]

 

 

F18

 

(1)

 

 

 

 

(3)

 

 

(4)

 

(2)

 

 

[170BT/BF] [180BT/BF]

F19

(3)

(2)

(4)

(1)

 

[130BT/150BT/170BT/180BT]

F20

(5)

(1)

 

(2)

 

 

 

 

(3)

 

[150BF] [170BF] [180BF]

F21

 

 

17

Image 17
Contents 130BT Operator’s manual150BT/BF 170BT/BF 180BT/BF English 115FEDERAL EMISSION CONTROL WARRANTY STATEMENT Safety ContentsMaintenance Warning labels on the machineWarning labels on the machine SafetySAFETY FIRST SymbolsSafety Precautions Symbols on the machineWORKING CONDITIONS AVOID NOISE PROBLEMWORKING CIRCUMSTANCE WORKING PLANBEFORE STARTING THE ENGINE USING THE PRODUCTSTORAGE MAINTENANCETRANSPORTATION 130BT What is what?150BF 150BT/BF150BT 170BF 170BT/BF170BT 180BF 180BT/BF180BT prEN15503 ISO7917 dB A Technical dataAssembly „ HARNESS „ BLOWER TUBES„ WAIST BELT 150BT/BF 170BT/BF 180BT/BF F9 F10 F11„ HOW TO MIX FUEL Fuel„ FUEL „ FUELING THE UNITOperation „ STOPPING ENGINE „ ADJUSTING IDLE SPEED„ AIR CLEANER Maintenance„ SPARK PLUG „ FUEL FILTERF32 F33 „ MUFFLER„ AIR INLET NET Storage„ IGNITION COIL AIR GAP INSPECTION „ SHOLDER STRAP