Husqvarna SPM1702SM manual Cooling system, Spark plug, Two-piece shaft, Air filter

Page 21

MAINTENANCE

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

4

3

2

1

The cooling system consists of:

1Air intake on the starter.

2Fins on the flywheel.

3Cooling fins on the cylinder.

4Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

Spark plug

The spark plug condition is influenced by:

Incorrect carburettor adjustment.

An incorrect fuel mixture (too much or incorrect type of oil).

A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm. The spark plug should be replaced after about a month in operation or earlier if necessary.

CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Two-piece shaft

(323LD, 325LDx)

The drive shaft end in the lower shaft should be lubricated with grease every 30 hours. There is a risk that the drive shaft ends (splined coupling) on models with two-piece shafts will seize if they are not lubricated regularly.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

Carburettor malfunctions

Starting problems

Loss of engine power

Unnecessary wear to engine parts.

Excessive fuel consumption.

Clean the filter every 25 hours, or more regularly if conditions are exceptionally dusty.

Cleaning the air filter

Remove the air filter cover and take out the filter. Wash it clean in warm, soapy water. Ensure that the filter is dry before refitting it.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

If the machine is used in dusty conditions the air filter should be soaked in oil. See instructions under the heading Oiling the air filter.

English – 21

Image 21
Contents 323L 323LD 325CX 325LX 325LDX Symbols KEY to SymbolsContents Dear Customer IntroductionWhat is what? What is WHAT?Personal protective equipment General Safety PrecautionsMachine′s safety equipment Stop switchThrottle lockout Cutting attachment guard Vibration damping systemMuffler Cutting equipment Locking nutTrimmer head Assembly AssemblyFitting the loop handle Assembling and dismantling the two-piece shaftFitting other guards and cutting attachments Assembling the cutting equipmentGuard Fitting the trimmer guard and trimmer headFuel safety Fuel HandlingFuel Mixing FuellingCheck before starting Starting and StoppingStarting and stopping StartingStopping Working Techniques Basic safety rulesGeneral working instructions Basic working techniquesTrimming Grass trimming with a trimmer headCarburettor MaintenanceCorrectly adjusted carburettor Fine adjustment of the idle speed TMuffler High speed jet HCooling system Cleaning the air filterSpark plug Two-piece shaftBevel gear Oiling the air filterMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataTechnical data 325Cx 325Lx 325LDx Engine Approved accessories Art No Use with EN292-2, Cispr 121997, EN ISO EC-declaration of conformity Applies to Europe only095 ~2,0 m Page 10 cm Clic 15 cm 25 m 095-.10610 cm 15 cm Clic 10 cm 05 m 15 cm Clic 75 m 079-0.0952,4 mm 079-0.095 75 m x Clic 1150257-26 ´z+R9h¶6¢¨ ´z+R9h¶6¢¨