Image 831.21007 manual Trouble-Shooting

Page 16

TROUBLE-SHOOTING

Most problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free at 1-877-897-7493, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time.

1.SYMPTOM: THE SPA WILL NOT OPERATE

a.Check the power cord. The power cord must be plugged into a grounded outlet (see PLUGGING IN THE RENEW 207 on page 10).

b.Check the GFCI breaker to see if it is tripped or if it was not turned on. Reset the GFCI breaker.

2.SYMPTOM: THE CIRCUIT BREAKER OR GFCI BREAKER TRIPS WHILE THE SPA IS OPERATING

a.Reset the circuit breaker. If the circuit breaker trips again, contact a qualified electrician for service.

3.SYMPTOM: THE PUMP HUMS

a.The filter may be dirty or damaged. Remove the filter from the filter housing of the spa jet unit and clean or replace the filter.

b.The pump may have a foreign object stuck in the impeller. Contact our customer service department or, if your spa is no longer under warranty, you may also contact a local spa and pool service provider.

c.The pump may have a loose wire connection. Contact our customer service department or, if your spa is no longer under warranty, you may also contact a local spa and pool service provider.

4.SYMPTOM: THE PUMP HUMS BUT DOES NOT ROTATE

a.The pump may be jammed. Contact our cus- tomer service department. If your spa is no longer under warranty, you may wish to contact a local spa and pool service provider.

5.SYMPTOM: THE PUMP IS NOISY WHILE OPERATING

a.There may be debris in the pump. Contact our customer service department. If your spa is no longer under warranty, you may wish to contact a local spa and pool service provider.

b. The pump may have a bad bearing. Contact our customer service department. If your spa is no longer under warranty, you may wish to con- tact a local spa and pool service provider.

6.SYMPTOM: THE WATER DOES NOT HEAT

a.The pump in the spa jet unit is the heater. If the pump is operating, the water should heat. Cover the RENEW 207 with the spa cover. The spa cover must be tight with the insulating liner in place. Set the air control to low. The water will heat at a rate of 3.0¡ F per hour. If you are using the spa indoors, and the room temperature is maintained at 70¡ F, it will take approximately 10 to 15 hours for the water to reach the set temperature.

b.If you are using the RENEW 207 outdoors, it may take longer for the water to heat. See the chart below for the approximate heating time.

Air Temperature

Heating Time

70¡ F +

10 to 15 hours

50¡ F to 70¡ F

16 to 25 hours

30¡ F to 50¡ F

26 to 30 hours

b. If the water still has not heated after four days, contact our customer service department or, if your spa is no longer under warranty, you may also contact a local spa and pool service provider.

7.SYMPTOM: THE SPA CONTINUES TO RUN AFTER IT HAS BEEN SHUT OFF

a.To turn the spa jets on, press the pump control once. To turn the spa jets off, press the control again. After you press the control once, the spa jets will shut off for about 30 seconds and then restart. Press the control again. The spa jets will remain off for 20 minutes, at which time they will begin running the filter cycle. Note: At any time after the spa jets have been shut off, the pump will begin cycling the water if the tem- perature falls below the minimum setting.

16

Image 16
Contents QUESTIONS? Model No Serial NoCustomer HOT Line Mon.ÐFri., 6 a.m.Ð6 p.m. MSTTable of Contents Page Page Page Before YOU Begin If you set up the Renew 207 inside If you set up the Renew 207 outsideChoosing a Location for the Renew Do not use an extension cord with the RenewSET-UP and Assembly Insulating Liner Posting the Warning Sign Using the RenewPlugging in the Renew Using the Console Testing and Treating the WaterStarting the Renew When the spa is not Securing the SPA CoverAlways keep Buckles lockedMaintenance Removing and Attaching the Access Cover Water ChemistryMaintaining the Proper PH Balance Draining the RenewWinter USE and Care TROUBLE-SHOOTING Symptom the Water is not Being Cleaned by the Filter Symptom the Water Pulsates or There is Minimum Water FlowSymptom the Water Level Drops Part LISTÑModel No Qty DescriptionExploded DRAWINGÑModel No Limited Hydrotherapy SPA Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT

831.21007 specifications

Image 831.21007 represents a pioneering advancement in modern imaging technology, showcasing a harmonious blend of state-of-the-art features that cater to the evolving demands of users across various domains. This image not only reflects exceptional visual quality but also embodies the innovation that defines contemporary visual media.

One of the standout characteristics of Image 831.21007 is its resolution, which offers an impressive level of detail. With ultra-high-definition capabilities, users can experience crisp, clear visuals that enhance both personal and professional applications. Whether utilized in digital art, photography, or scientific visualization, the image ensures that every intricate detail is preserved, enabling users to engage deeply with the content.

In addition to its resolution, Image 831.21007 employs cutting-edge color reproduction technologies. Leveraging advanced color management systems, this image excels in delivering vibrant and accurate hues that resonate with viewers. The ability to reproduce colors that closely resemble real-life shades is particularly beneficial for fields such as graphic design and marketing, where visual fidelity is paramount.

The image’s dynamic range is another notable feature, allowing for a wide spectrum of brightness levels. With highlights and shadows rendered with exceptional clarity, viewers can appreciate nuances that would be lost in lesser-quality visuals. This dynamic range capability makes Image 831.21007 ideal for applications like video production and cinematic presentations, where lighting conditions can vary significantly.

Furthermore, Image 831.21007 is optimized for compatibility with various software and hardware platforms, ensuring seamless integration into existing workflows. This adaptability is crucial for users who operate in diverse technological environments, enabling them to maximize the potential of their creative tools without facing compatibility issues.

Lastly, the image is designed with user experience in mind, featuring intuitive interfaces that simplify navigation and usage. Whether for casual viewing or professional editing, Image 831.21007 empowers users by providing accessible functionality alongside its robust feature set.

In summary, Image 831.21007 stands out as a hallmark of modern imaging excellence, characterized by high resolution, superior color accuracy, an extensive dynamic range, compatibility, and user-friendly design. It embodies the future of visual media, catering to the growing demand for exceptional quality across countless applications. With such a rich set of features, this image is poised to inspire creativity and innovation in various fields.