Vita Spa U -1 3 0 Testing the Gfci, Displaying Time or Water Temperature, Setting Temperature

Page 15

CONTROLS & OPERATING INSTRUCTIONS

Note: For best results, read each step carefully and entirely before proceeding to the next.

TESTING THE GFCI

The GFCI shuts off the electricity in a fraction of a second if there is ashort anywhere in the system. It is rec- ommended that the GFCI be tested prior to each use. Test as follows:

1.Push the TEST button on the GFCI. The RESET button with trip out, the topside digital control LED display with go out. If this does not happen,

DO NOT USE SPA. Check all wire connection to assure that all are tight and not exposed to moisture.

2.If the GFCI test properly, firmly push the REST button back into place. The topside digital control LED will come back on.

3.If the GFCI trips by itself at anytime, firmly press the reset button back into place and perform the above test. If this happens more than once,

DO NOT USE THE SPA. Check for loose wires or moisture.

The initial factory settings can be changed by following the instructions shown below.

A. Displaying Time or Water Temperature

Pressing the “PROG”button will allow switching the display between time and water temperature. The dis- played temperature is the last reading taken when the pump was operational. To verify water temperature when the pump is shut off, press the jet button and allow the pump to run for two minutes. The water tem- perature sensor will analyze the water temperature during this time period and then display the current water temperature.

B. Setting Temperature

1.Press the “PROG”button to display water temperature

2.Press the “UP”or “DOWN”arrow to select the desired temperature.

3.Press the “PROG”button to exit the programming mode.

C. Setting Time and Filtration Hours

1.Press and hold the “PROG”button for 5 seconds until the displayed hour starts to flash.

2.Press the “UP”or “DOWN”arrow to select the current hour.

3.Press the “PROG”button one or more item to display minutes.

4.Press the “UP”or “DOWN”arrow to select the current minutes

5.Press the “PROG”button one more item to display the filtration hours F=4H (default) will be flashing. Refer to “Filtration Cycles”section to determine the length of cycles (F=4H or F=8H) you prefer.

6.Press the “UP”or “DOWN”arrow to select the filtration cycle desired.

7.Press the “PROG”button to exit the programming mode.

— 13 —

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Deluxe Table of Contents Owner’s Record Importantsafetyinstructions DON’T DO’S & DON’TSPage Installation Instructions In-Line Ground Fault Circuit Installation DiagramsVolts 3-wire systems Clearances Separate Neutral & Solid Ground Common Neutral Ground BAR Main Page Page Tighten Securely Do not USE Aluminum WireADD Start UP Chemicals Fill Your SPASetting Time and Filtration Hours Testing the GfciDisplaying Time or Water Temperature Setting TemperatureMemory Auto Heat OperationJet Button Single Pump System Light ButtonResetting Your Spa Winterizing Your SPA SPA MaintenanceRemove the filter and clean as required Draining Your SPANever RUN SPA Without Filter Filter MaintenanceTo clean the filter To clean and condition the vinyl coverOptional Lightning Series Water Purification System Water Quality MaintenanceSanitizing PH ControlDiagnostic & Troubleshooting Maintenance Record Schematic U130 ECO Spas 2320 NW 147th Street Miami, Florida

U -1 3 0 specifications

The Vita Spa U-1 3 0 is an exquisite fusion of luxury and innovation, designed to elevate your relaxation experience. This spa model promises not only unparalleled comfort but also cutting-edge technology to enhance hydrotherapy benefits.

One of the main features of the U-1 3 0 is its spacious design, allowing ample room for multiple users. Its ergonomic seating arrangements provide optimal support to your body, ensuring a soothing experience whether you are soaking alone or enjoying time with friends and family. The layout is crafted to promote social interaction while still allowing for individual relaxation.

A standout characteristic of the Vita Spa U-1 3 0 is its advanced hydrotherapy system. The spa is equipped with strategically positioned jets that deliver a powerful yet gentle massage. Users can adjust the intensity and direction of the jets, focusing on areas that require extra attention. The multi-zone hydrotherapy functions effectively alleviate tension and promote circulation, making it an excellent choice for those seeking therapeutic benefits.

In terms of technology, the U-1 3 0 boasts an intelligent control system that allows users to customize their spa experience. The intuitive interface enables users to easily adjust water temperature, jet pressure, and lighting to create the perfect ambiance. Additionally, the spa features energy-efficient heating and filtration systems, ensuring that it operates quietly and with minimal environmental impact.

The design of the Vita Spa U-1 3 0 is not only aesthetic but also functional. With durable materials and a robust construction, it can withstand various weather conditions, making it suitable for both indoor and outdoor settings. The spa is available in a variety of colors and finishes, allowing users to choose a design that complements their personal style and outdoor decor.

Moreover, safety features are a priority in the U-1 3 0, which includes slip-resistant surfaces and a secure locking system. This ensures that users can enjoy their spa experience without worrying about accidents or unauthorized access.

In summary, the Vita Spa U-1 3 0 stands out in the market for its combination of luxurious features, innovative technologies, and thoughtful design. It provides an ideal solution for relaxation, hydrotherapy, and social interaction, making it a worthwhile investment for anyone looking to enhance their outdoor or indoor living space. Whether for personal enjoyment or gatherings with friends, the U-1 3 0 promises a rejuvenating experience.
Top Page Image Contents