Ryobi Outdoor RY49701 manual Specific Safety Rules

GENERAL SAFETY RULES

nDO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

nDO NOT OPERATE A TOOL WHILE UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR ANY MEDICATION.

nALWAYS carry the tool only by the carrying handle.

nUSE ONLY RECOMMENDED ACCESSORIES listed in this manual or addendums. Use of accessories that are not listed may cause the risk of personal injury. Instructions for safe use of accessories are included with the accessory.

nTOOL SERVICE MUST BE PERFORMED ONLY BY QUALIFIED REPAIR PERSONNEL. Service or mainte- nance performed by unqualified personal could result in a risk of injury.

nWHEN SERVICING use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.

nALWAYS STAY ALERT! Do not allow familiarity (gained from frequent use of your tool) to cause a careless mis- take. ALWAYS REMEMBER that a careless fraction of a second is sufficient to inflict severe injury.

nMAKE SURE THE WORK AREA HAS AMPLE LIGHTING to see the work and that no obstructions will interfere with safe operation BEFORE performing any work using your tool.

nALWAYS TURN OFF THE TOOL before disconnecting it to avoid accidental starting when reconnecting to power supply. NEVER leave the tool unattended while connected to a power source.

SPECIFIC SAFETY RULES

nDO NOT ALLOW anyone to operate the log splitter who has not read the operator’s manual or has not been instructed on the safe use of the splitter.

nNEVER ALLOW CHILDREN OR UNTRAINED ADULTS TO OPERATE THIS MACHINE.

nIF SOMEONE is helping load logs to be split, DO NOT start the machine until that person is clear of the area.

nNEVER ALLOW ANYONE TO RIDE ON THE MACHINE.

n�NEVER TRANSPORT ANYTHING OR ANYONE ON THE LOG SPLITTER.

n�HIGH FLUID PRESSURES ARE DEVELOPED IN HY- DRAULIC LOG SPLITTERS. Pressurized hydraulic fluid escaping through a pin hole opening can puncture skin and cause severe blood poisoning. Heed the following instructions at all times:

a)Do not operate the machine with frayed, kinked, cracked, or damaged hoses, fittings, or tubing.

b)Stop the engine and relieve hydraulic system pressure before changing or adjusting fittings, hoses, tubing, or other system components.

c)Do not adjust the pressure settings of the pump or value.

d)Never use your hand. Leaks can be located by passing cardboard or wood over the suspected area. Look for discoloration. If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not adminis- tered immediately.

nKEEP THE OPERATOR ZONE and adjacent area clear for safe, secure footing.

nLOG SPLITTERS SHOULD BE USED ONLY for splitting wood. DO NOT use for other purposes unless the manu- facturer provides attachments and instructions.

nMAKE SURE THE LOG SPLITTER is on a level surface. Block the splitter as required to prevent unintended move- ment.

nALWAYS OPERATE the splitter from the manufacturer’s indicated operator zone.

nLOGS TO BE SPLIT ON RAM-TYPE UNITS should be cut as squarely as possible.

nTHE MACHINE OWNER should instruct anyone assisting him or her in safe log splitting operation.

nALWAYS operate the log splitter with all safety equip- ment in place and all controls properly adjusted for safe operation.

nALWAYS operate the log splitter at manufacturer’s rec- ommended speed.

nWHEN LOADING a ram-type log splitter, place your hands on the sides of the log not at the ends. NEVER place your hands or any part of your body between a log and any part of the log splitter.

nON RAM-TYPElog splitters, NEVER attempt to split more than one (1) log at a time unless the ram has been fully extended and a second log is needed to complete the separation of the first log.

n�ON RAM-TYPElog splitters on which the logs are not square, the longest portion of the log should be rotated down and the most square end placed against the ram.

nCLEAR DEBRIS from moving parts but only when the power source is shut off.

nUSE ONLY YOUR HAND TO OPERATE THE LOG SPLITTER CONTROLS.

nALWAYS UNPLUG FROM THE POWER SOURCE while repairing or adjusting the splitter except as recommended by the manufacturer.

nCIRCUIT CAPACITY AND FUSES:

a)Use only an electrical circuit having adequate capacity as recommended by the log splitter manufacturer.

b)“Blowing” a fuse or tripping a circuit breaker is usually a warning that you are overloading the machine or have too many devices taking power from the circuit, or both. Do not install a higher capacity fuse!

nLEARN AND UNDERSTAND all controls and the proper use of the equipment.

nSAVE THESE INSTRUCTIONS. Refer to them frequently and use to instruct other users. If you loan someone this tool, loan them these instructions also.

4