Porter-Cable D21679-008-0 To Start the Engine, Stopping Engine, Connecting Electrical Loads

Page 12

TO START THE ENGINE

Never run engine indoors or in enclosed, poor ventilated areas, engine exhaust contains carbon monoxide, an odorless and deadly gas.

1.Open the fuel shut-off valve. Turn counter clockwise until the valve stops.

2.Place the ON/OFF switch located on the engine in the ON position.

3.Move the choke control located on the engine to "CHOKE" position.

NOTE: No choke is required on warm engines. Make sure choke is in the "RUN" position on warm engine starts.

4.Grasp handle on rope starter and pull slowly until resistance is felt. Let the rope rewind slowly. Pull rope with a rapid full arm stroke. Let rope rewind slowly. Repeat if necessary.

Low Oil Light

NOTE: IF ENGINE OIL LEVEL IS TOO LOW, ENGINE WILL NOT START. CHECK OIL LEVEL AND ADD IF NECESSARY.

NOTE: LOW OIL LIGHT WILL "FLICKER" WHEN ROPE STARTER IS PULLED IF ENGINE OIL IS LOW.

5.When engine starts, gradually move the choke to the "RUN" position.

IMPORTANT: Allow generator to run at no load for

5minutes upon each initial start-up to allow engine and generator to stabilize.

STOPPING ENGINE

1.Disconnect all electrical loads.

2.Turn ON/OFF switch to "OFF" position.

3.Close fuel shut-off valve.

CONNECTING ELECTRICAL LOADS

1.Let engine run and warm up for five minutes after starting with no electrical load.

Connect loads in the following manner to prevent damage to equipment:

2.Connect inductive load equipment first, inductive loads consist of refrigerators, freezers, water pumps, air conditioners, or small hand tools. Connect the items that require the most wattage first. See Wattage Calculation Section in this manual.

3.Connect the lights next.

4.Voltage sensitive equipment should be the last equipment connected to the generator. Plug voltage sensitive appliances such at TV's, VCR's, micro- waves, ovens, computers, and cordless tele- phones into a UL listed voltage surge protector, then connect the UL listed voltage surge protector to the generator.

Failure to connect and operate equipment in this sequence can cause damage to equipment and will void the warranty on your generator.

Follow the wattage calculation table in the Wattage Calculation section of this manual. Overloading the generator will cause power fluctuations and can damage equipment and appliances.

Porter-Cable Corporation will only be responsible for damage to customer's equipment when the generator is determined to be defective. This determination will only be made by an authorized representative of Porter- Cable Corporation and this decision will be final. Porter-Cable Corporation reserves the right to inspect the electrical connections at the customer's site of operation and test the generator for proper operation before any determination of liability is made. Failure to maintain the equipment or wiring for inspection will void any claim for damages by the customer. Porter-Cable Corporation will not be responsible for equipment damaged as a result of voltage surges, improper operation or improper installation of the generator.

12 — ENG

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Instruction Manual Generator Specification ModelWarranty This Warranty is not Transferable and does not CoverSafety Guidelines Definitions Important Safety InstructionsHazard What could Happen HOW to Prevent IT Risk of Electrocution and FireOperation of generator in rain Wet, icy, or flooded conditionsRisk of Fire Do not Operate UnitDoors or in ANY Confined AreaRisk of Breathing Inhalation Hazard Risk of Unsafe Operation Listed voltage surge protecGenerator Risk of HOT Surfaces Risk of Moving PartsRisk from Lifting Assembly Extension Cord Wire Gauge Chart LengthRemove Generator from Carton Grounding the GeneratorOperation Connecting Electrical Loads To Start the EngineStopping Engine Maintenance StorageWattage Calculations Running Watts Starting WattsStarting Wattage Requirements Volts X Amp = Watts Volts x 10 amps = 1200 wattsHousehold Wattage Calculator Appliance or Load Device Typical Device Wattage TotalTroubleshooting Guide Problem Cause CorrectionENG ENG Generator Quick Facts

D21679-008-0 specifications

The Porter-Cable D21679-008-0 is an exceptional tool designed for professionals and DIY enthusiasts seeking reliability and efficiency in their projects. Known for its robust performance and innovative features, this tool has become a staple in various industries, particularly in woodworking and construction.

One of the main features of the D21679-008-0 is its powerful motor, delivering consistent performance that enhances productivity. The motor is designed for heavy-duty applications and can handle a variety of tasks with ease. Coupled with a well-designed gear system, the tool ensures smooth operation and longevity, making it a smart investment for any toolkit.

Another key feature is its lightweight and ergonomic design. The D21679-008-0 is engineered for comfort during prolonged use. Its balanced weight distribution minimizes user fatigue, allowing for extended periods of operation without discomfort. The soft-grip handle provides additional control, giving users a confident grip even in challenging working conditions.

The D21679-008-0 incorporates advanced technology that elevates its performance. It features precision-engineered components that optimize cutting efficiency, ensuring clean and accurate results. Additionally, the tool is equipped with a variable speed control function, allowing the user to adjust the speed according to the material and application. This versatility makes it suitable for cutting through different materials, from softwoods to harder composites.

Safety is also a significant consideration in the design of the D21679-008-0. It includes several safety features such as a protective blade guard that minimizes the risk of accidental contact while in use. This thoughtful incorporation of safety measures reflects Porter-Cable’s commitment to user protection and functionality.

Durability is another characteristic that sets the D21679-008-0 apart. The tool is constructed from high-quality materials that withstand the rigors of daily use. This robust construction not only prolongs the tool's lifespan but also contributes to its reliability in various working environments.

In summary, the Porter-Cable D21679-008-0 stands out due to its powerful motor, ergonomic design, advanced technology, emphasis on safety, and durable construction. These features make it an essential tool for anyone looking to enhance their efficiency and precision in woodworking and construction tasks. Whether for professional use or home improvement projects, this tool delivers an outstanding performance that meets the demands of any user.
Top Page Image Contents