Poulan WT200 Maintain Your Unit Properly, Blower Tube Assembly, Vacuum BAG Assembly

disconnected. Keep vents and discharge tubes free of debris which can accumulate and restrict proper air flow.

DNever place any object in the air intake open- ing as this could restrict proper air flow and

cause damage to the unit.

DNever use for spreading chemicals, fertiliz- ers, or other substances which may contain

toxic materials.

DTo avoid spreading fire, do not use near leaf or brush fires, fireplaces, barbecue pits, ashtrays, etc.

DUse only for jobs explained in this manual.

MAINTAIN YOUR UNIT PROPERLY

D Have all maintenance other than the rec- ommended procedures described in the in- struction manual performed by an autho- rized service dealer.

D Disconnect spark plug before performing maintenance except for carburetor adjust- ments.

D Use only recommended PoulanŽ replace- ment parts; use of any other parts may void your warranty and cause damage to your unit.

D Empty fuel tank before storing the unit. Use up fuel left in carburetor by starting engine and letting it run until it stops.

D Do not use any accessory or attachment other than those recommended by manufac- turer for use with your unit.

D Do not store the unit or fuel in a closed area where fuel vapors can reach sparks or an open flame from hot water heaters, electric motors or switches, furnaces, etc.

D Store in a dry area out of reach of children.

SPECIAL NOTICE: Exposure to vibra- tions through prolonged use of gasoline pow- ered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swelling. Prolonged use in cold weather has been linked to blood vessel dam- age in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An antivibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condi- tion of this tool.

SPECIAL NOTICE: For users on U.S. For- est Land and in some states, including Cali- fornia (Public Resources Codes 4442 and 4443), Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington: Certain internal combustion engines operated on forest, brush, and/or grass covered land in the above areas are required to be equipped with a spark arresting screen, maintained in effec- tive working order, or the engine must be con- structed, equipped, and maintained for the prevention of fire. Check with your state or lo- cal authorities for regulations pertaining to these requirements. Failure to follow these requirements is a violation of the law. This unit is not factory equipped with a spark arresting screen; however, a spark arresting screen is available as an optional part. If a spark arrest- ing screen is required in your area, contact your authorized service dealer for the correct kit. The spark arresting screen, blower tubes, and nozzles must be assembled to unit to be in full compliance with regulations.

WARNING: Stop engine and be sure the impeller blades have stopped turning be- fore opening the vacuum inlet door or at- tempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or ac- cessing movable parts.

WARNING: If you receive your unit assembled, check each step to insure your unit is properly assembled and all fasteners are secure. Follow all safety information in the manual and on the unit.

DA standard screwdriver is required for as- sembly.

BLOWER TUBE ASSEMBLY

1.Align the rib on the blower tube with the groove in the blower outlet; slide the tube into place.

NOTE: Tube clamp must be loose enough to allow blower tube to be inserted in blower out- let. Loosen tube clamp by turning knob coun- terclockwise.

Blower

Outlet Blower

Tube

Groove Rib

2.Tighten the tube clamp by turning the knob clockwise.

3.To remove the tube, turn the knob counter- clockwise to loosen clamp; remove tube.

VACUUM BAG ASSEMBLY

1.Open the zipper on the vacuum bag and insert the elbow tube.

2.Push the small end of the elbow tube through the small opening in the bag.

-- 3 --