Poulan 183041 To Adjust Gauge Wheels See Fig, To Operate on Hills, To Operate Mower See Fig

Page 12
3/8-16
LOCKNUT
GUAGE WHEEL MOUNTING BRACKET

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/BRAKE PEDAL IS DEPRESSED.

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 5 and 9)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attach- ment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

"ENGAGED" POSITION

 

ATTACHMENT

 

LIFT LEVER

 

HIGH POSITION

 

LOW

 

POSITION

ATTACHMENT

DEFLECTOR

CLUTCH LEVER

SHIELD

"DISENGAGED"

 

POSITION

 

FIG. 8

FIG. 9

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PR17H42STF Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet KeyAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Mower Cutting Height See Fig Stopping See FigTo SET Parking Brake See Fig To USE Throttle Control See FigTo Adjust Gauge Wheels See Fig To Operate on HillsTo Operate Mower See Fig To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsLubrication Chart Service DatesCustomer Responsibilities General RecommendationsTractor Engine Cleaning Engine Cooling FinsAIR Filter MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PR17H42STF, Product Number 954 56Electrical KEY Part Description Chassis and Enclosures 158112 Keeper Belt Rear Lh Drive Repair Parts Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine 170551 Control Th/ch Flag Mower Deck 179748 Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Page Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183041 specifications

The Poulan 183041 is an essential tool for homeowners and landscaping professionals alike, designed to make yard work more efficient and manageable. Known for its reliability and ease of use, the Poulan 183041 is a high-quality gas-powered string trimmer that stands out in the realm of outdoor power equipment.

One of the main features of the Poulan 183041 is its robust 25cc two-cycle engine. This powerful engine delivers ample power for trimming grass, weeds, and tough brush, making it suitable for a variety of landscaping tasks. The lightweight design, weighing approximately 10 pounds, ensures that users can maneuver the trimmer easily, reducing fatigue during extended use.

The trimmer is equipped with an easy-start system, which allows users to start the engine with minimal effort. This feature is particularly beneficial for those who may struggle with traditional pull-start mechanisms. Furthermore, the Poulan 183041 has a straight shaft design, providing extended reach for trimming in hard-to-reach areas like under bushes and fences.

The dual-line cutting system is another significant characteristic of this model. It utilizes a 0.080-inch line, which offers a practical balance between durability and cutting ability. The bump feed mechanism allows for quick and efficient line advancement, ensuring that users can maintain trimming without interruptions.

The Poulan 183041 also features an adjustable handle, which provides users the flexibility to customize their grip for optimal comfort and control. Combined with anti-vibration technology, it significantly reduces hand fatigue and enhances the overall user experience.

Moreover, the trimmer’s design includes a protective debris guard, which minimizes the risk of projectiles while trimming, promoting safety during operation.

In addition to these features, Poulan emphasizes ease of maintenance with the 183041 model. Regular upkeep is straightforward, reducing downtime and prolonging the equipment's lifespan. This trimmer is engineered for convenience, allowing users to focus on their lawn care tasks efficiently.

Overall, the Poulan 183041 is a dependable and versatile string trimmer that delivers power and comfort, making it an excellent choice for anyone looking to maintain their yard with ease. Whether tackling tough weeds or giving the edges a clean finish, this model proves to be an indispensable asset for landscaping efforts.
Top Page Image Contents