Poulan 183041 owner manual To Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO ADJUST BRAKE (See Fig. 23)

Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

•Depress clutch/brake pedal and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING BRAKE “ENGAGED”

 

NUT

 

1-9/16"

“A”

JAM NUT

 

OPERATING

ARM

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUST- MENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/DEPARTMENT

FIG. 23

TO REPLACE MOTION DRIVE BELT (See Fig. 24)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this section of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEY

FIG. 24

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMIS- SION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT(See Fig. 25)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PR17H42STF IV. Service Safety RulesGeneral Operation II. Slope OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Seat Unassembled PartsSlope Sheet KeyTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor To Adjust Mower Cutting Height See Fig Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control See FigTo Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMulching Mowing Tips Mowing TipsService Dates Lubrication ChartCustomer Responsibilities General RecommendationsTractor Engine Engine Cooling Fins CleaningAIR Filter MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Brake See FigTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Replace Headlight Bulb Interlocks and RelaysOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PR17H42STF, Product Number 954 56 SchematicElectrical KEY Part Description Chassis and Enclosures 158112 Keeper Belt Rear Lh Drive Repair Parts Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsEngine 170551 Control Th/ch Flag Mower Deck 179748 Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Page Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

183041 specifications

The Poulan 183041 is an essential tool for homeowners and landscaping professionals alike, designed to make yard work more efficient and manageable. Known for its reliability and ease of use, the Poulan 183041 is a high-quality gas-powered string trimmer that stands out in the realm of outdoor power equipment.

One of the main features of the Poulan 183041 is its robust 25cc two-cycle engine. This powerful engine delivers ample power for trimming grass, weeds, and tough brush, making it suitable for a variety of landscaping tasks. The lightweight design, weighing approximately 10 pounds, ensures that users can maneuver the trimmer easily, reducing fatigue during extended use.

The trimmer is equipped with an easy-start system, which allows users to start the engine with minimal effort. This feature is particularly beneficial for those who may struggle with traditional pull-start mechanisms. Furthermore, the Poulan 183041 has a straight shaft design, providing extended reach for trimming in hard-to-reach areas like under bushes and fences.

The dual-line cutting system is another significant characteristic of this model. It utilizes a 0.080-inch line, which offers a practical balance between durability and cutting ability. The bump feed mechanism allows for quick and efficient line advancement, ensuring that users can maintain trimming without interruptions.

The Poulan 183041 also features an adjustable handle, which provides users the flexibility to customize their grip for optimal comfort and control. Combined with anti-vibration technology, it significantly reduces hand fatigue and enhances the overall user experience.

Moreover, the trimmer’s design includes a protective debris guard, which minimizes the risk of projectiles while trimming, promoting safety during operation.

In addition to these features, Poulan emphasizes ease of maintenance with the 183041 model. Regular upkeep is straightforward, reducing downtime and prolonging the equipment's lifespan. This trimmer is engineered for convenience, allowing users to focus on their lawn care tasks efficiently.

Overall, the Poulan 183041 is a dependable and versatile string trimmer that delivers power and comfort, making it an excellent choice for anyone looking to maintain their yard with ease. Whether tackling tough weeds or giving the edges a clean finish, this model proves to be an indispensable asset for landscaping efforts.
Top Page Image Contents