Poulan 183359 owner manual Before Starting the Engine, ADD Gasoline, Check Engine OIL Level

Page 13

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

Check engine oil with tractor on level ground.

Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Customer Responsibilities section of this manual).

To change engine oil, see the Customer Responsibili- ties section in this manual.

ADD GASOLINE

Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: When operating in temperatures below32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather starting.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to sepa- ration and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 6)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

Place gear shift lever in neutral (N) position.

Move attachment clutch to “DISENGAGED” position.

Move throttle control to choke () position.

NOTE: Before starting, read the warm and cold starting procedures below.

Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke () position and retry.

WARM WEATHER STARTING (50° F and above)

When engine starts, move the throttle control to the fast position.

The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

When engine starts, allow engine to run with the throttle

control in the choke () position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the tempera- ture.

The attachments can also be used during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

13

Image 13
Contents PR1842STC Safe Operation Practices for Ride-On Mowers IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Contents of Hardware Pack HOW to SET UP Your Tractor Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig To Convert to Bagging or DISCHARG- ING To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Tractor Engine Muffler CleaningSpark Plugs Engine OIL FilterTo Remove Mower See Fig To Install Mower See FigTo Replace Mower Blade Drive Belt See Fig To Level Mower HousingTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See Fig To Adjust Steering Wheel AlignmentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Replace Headlight Bulb Interlocks and RelaysFuel System OtherEngine OIL CylindersTroubleshooting Points OFF Tractor - Model Number PR1842STC SchematicElectrical KEY Part Description Chassis and Enclosures Screw Hex Wshd 8-18 x 7/8 Drive Repair Parts Steering Assembly 180656 Wheel Steering KEY Part NO. NO. Description Seat AssemblyWheels and Tires DecalsEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line DegreeParts and Service

183359 specifications

The Poulan 183359 is a versatile and efficient chainsaw designed for both homeowners and professionals. Known for its reliability and power, this chainsaw features a robust engine and an array of advanced technologies that make it a top choice for cutting tasks, whether you're trimming branches or tackling larger trees.

One of the main features of the Poulan 183359 is its powerful 38cc two-stroke engine. This engine provides a balance of performance and efficiency, allowing users to cut through tough wood with ease while maintaining fuel economy. The chainsaw is designed to deliver a high power-to-weight ratio, ensuring that it remains lightweight and easy to handle without sacrificing cutting performance.

The Poulan 183359 incorporates an automatic oiling system, which is critical for maintaining the chain's lubrication during operation. This feature not only prolongs the life of the chain but also enhances cutting efficiency by reducing friction. The adjustable flow allows users to customize the oil output depending on the specific task, ensuring optimal performance in various cutting conditions.

Safety is a paramount concern with any power tool, and the Poulan 183359 does not disappoint in this area. It includes a chain brake that can be activated to halt the chain immediately in case of kickback. Additionally, the chainsaw is equipped with a front hand guard, which protects the user's hands from debris and potential injuries while operating.

The design of the Poulan 183359 also emphasizes user comfort. It features an anti-vibration system that minimizes vibrations transferred to the user's hands, reducing fatigue during extended periods of use. Moreover, the ergonomic handle design provides a secure grip, enabling precise control while cutting.

Another notable characteristic is its easy-start technology, which makes starting the engine simpler and more reliable. This feature is particularly beneficial for users who may struggle with traditional starting methods, allowing them to get to work quickly.

With its combination of power, safety features, and user-friendly design, the Poulan 183359 is highly regarded in its category. Whether you are a seasoned professional or a homeowner looking to tackle yard work, this chainsaw delivers performance and reliability, making it an essential tool for any outdoor project. Its well-rounded capabilities make it a dependable choice for those seeking an effective and efficient cutting solution.