Poulan 952802326, SM4218AVX, 545167697 BAR and Chain Lubrication, Important Points to Remember

Page 10

WARNING: Alternative fuels (not gasoline) such as E--15 (15% alcohol), E--20 (20% alcohol), E--85 (85% alcohol) are NOT classified as gasoline and are NOT approved for use in 2--stroke gasoline engines. Use of al- ternative fuels will cause problems such as: im- proper clutch engagements, overheating, va- por lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor components, etc. Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar. In freezing weath- er oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil sys- tem to pump enough oil for adequate lubrica- tion. Genuine Poulan or Poulan PRO bar and chain oil is recommended to protect your unit against excessive wear from heat and fric- tion. Poulan or Poulan PRO oil resists high temperature thinning.

If Poulan or Poulan PRO bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri- cation.

SAlways stop the engine before removing the oil cap.

CHAIN BRAKE

Ensure chain brake is disengaged by pulling the front hand guard back toward the front han- dle as far as possible. The chain brake must be disengaged before cutting with the saw.

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15-- 18(40 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

Right Foot Through Rear Handle

WARNING: Do not attempt to throw or drop--start the chain saw. Doing so will put the operator at risk of serious injury due to loss of control of the chain saw.

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope rewind slowly. For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

IGNITION

SWITCH

ON

STOP

Choke

Lever

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

10

Image 10
Contents Manual de Instrucciones Manuel d’Instructions Starting Reminder Using the chain sawAlways use two hands when operating the chain saw Chain TensioningMaintain Your SAW in Good Working Order Plan AheadOperate Your SAW Safely Handle Fuel with CautionMaintain Control KickbackReduce the Chance of Kickback Avoid Pinch-KickbackChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle If your hand slips off the front handlebarAttaching the BAR & Chain If AssemblyLoosen Adjusting the tension CuttersTighten OperationKnow Your Chain SAW ON/STOPThrottle LOCK-OUT ON/STOP Switch Chain BrakeThrottle Trigger Chain TensionBAR and Chain Lubrication Important Points to RememberBraking function control Caution The chain brake must be Starting a Warm EngineDifficult Starting or starting a flooded engine Inertia activating function controlFelling Large Trees Tree Felling TechniquesNotch CUT and Felling the Tree Important Points Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingLimbing ServiceLimbing and Pruning Important Points PruningCheck for Loose Fasteners and Parts General RecommendationsCheck for Damaged or Worn Parts Check Chain SharpnessCleaning the Spark ARREST- ING Screen Inspect and Clean Unit and DecalsClean AIR Filter Check Chain BrakeChain Sharpening Chain AdjustmentReplace Fuel Filter Tools requiredStorage Load Adjustment Engine Empty fuel tank and refill withPoulan PRO Ligations The U.S. Environmental

545167697, SM4218AVX, 952802326 specifications

The Poulan 952802326, SM4218AVX, and 545167697 are essential tools for anyone seeking reliable outdoor power equipment, particularly in the domain of chainsaws and forestry tools. Known for their powerful performance and user-friendly features, these models represent a blend of innovation and practicality.

The Poulan 952802326 is particularly noted for its compact design, which makes it a favorite among homeowners and professionals alike. It boasts a robust 18-inch bar and chain, allowing for efficient cutting of medium-sized trees and limbs. The 40cc two-stroke engine provides ample power for demanding tasks while maintaining a lightweight construction that minimizes fatigue during extended use. One of its standout features is the Easy Start technology, which reduces the effort required to start the engine, making it accessible for users of all skill levels.

The SM4218AVX model is engineered for versatility, equipped with a 42cc engine that balances power and efficiency. Its low-vibration design enhances user comfort, significantly reducing strain during operations. This chainsaw also features an automatic oiling system that ensures optimal lubrication of the bar and chain, extending their lifespan and reducing maintenance efforts. The Quick-Release air filter allows for easy access, promoting better engine performance and longevity.

The Poulan 545167697 represents a leap in technology with its advanced safety features. It includes a chain brake that activates in case of kickback, ensuring the user's protection. Additionally, the anti-vibration system adds to the overall safety, making the chainsaw easier to control and maneuver. Its lightweight nature does not compromise its rugged durability, making it ideal for both professional logging and home landscaping projects.

Each of these Poulan models embodies a commitment to quality and performance. With user-friendly controls, efficient fuel consumption, and advanced safety mechanisms, they cater to a wide range of users, from casual homeowners to seasoned professionals. Their design reflects a focus on not only power and efficiency but also on user comfort and safety, ensuring that even demanding tasks can be completed with confidence and ease. Whether tackling heavy-duty forestry projects or simple backyard maintenance, the Poulan 952802326, SM4218AVX, and 545167697 stand out as reliable companions in outdoor power equipment.