Poulan SM4218AVX, 952802326, 545167697 instruction manual Storage

Page 18

CARBURETOR ADJUSTMENT

WARNING: The chain will be moving during most of this procedure. Wear your pro- tective equipment and observe all safety pre- cautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T

adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

COOLING SYSTEM

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

SAir intake on the starter S Air guide plate

S Fins on the flywheel

S Cooling fins on the cylinder

S Cylinder cover (directs cold air over the cylinder)

Clean the cooling system with a brush after each use, more often in demanding condi- tions. A dirty or blocked cooling system re- sults in the machine overheating which causes damage to the piston and cylinder.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place

and position chain saw so that any sharp object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more.

If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage. S Store in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

S Oil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum depos- its during storage. Add stabilizer to the gaso- line in the fuel tank or fuel storage container. Follow the mix instructions found on stabiliz- er containers. Run engine at least 5 minutes after adding stabilizer.

Poulan/WEED EATER 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you can add a fuel stabilizer to your fuel tank.

HELPFUL TIP

During storage of your gas/ oil mixture, the oil will sepa- rate from the gas.

We recommend that you shake the gas can weekly to insure proper blending of the gas and oil.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through

the spark plug opening. Slowly pull the start- er rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of rec- ommended type and heat range.

SClean air filter.

SCheck entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

SAt the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to

another.

S Replace your gasoline can if it starts to rust.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Manual de Instrucciones Manuel d’Instructions Starting Reminder Using the chain sawAlways use two hands when operating the chain saw Chain TensioningMaintain Your SAW in Good Working Order Plan AheadOperate Your SAW Safely Handle Fuel with CautionMaintain Control KickbackReduce the Chance of Kickback Avoid Pinch-KickbackChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle If your hand slips off the front handlebarAssembly Attaching the BAR & Chain IfLoosen Adjusting the tension CuttersTighten OperationKnow Your Chain SAW ON/STOPThrottle LOCK-OUT ON/STOP Switch Chain BrakeThrottle Trigger Chain TensionBAR and Chain Lubrication Important Points to RememberBraking function control Caution The chain brake must be Starting a Warm EngineDifficult Starting or starting a flooded engine Inertia activating function controlTree Felling Techniques Felling Large TreesNotch CUT and Felling the Tree Important Points Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingLimbing ServiceLimbing and Pruning Important Points PruningCheck for Loose Fasteners and Parts General RecommendationsCheck for Damaged or Worn Parts Check Chain SharpnessCleaning the Spark ARREST- ING Screen Inspect and Clean Unit and DecalsClean AIR Filter Check Chain BrakeChain Sharpening Chain AdjustmentReplace Fuel Filter Tools requiredStorage Load Adjustment Engine Empty fuel tank and refill withPoulan PRO Ligations The U.S. Environmental

545167697, SM4218AVX, 952802326 specifications

The Poulan 952802326, SM4218AVX, and 545167697 are essential tools for anyone seeking reliable outdoor power equipment, particularly in the domain of chainsaws and forestry tools. Known for their powerful performance and user-friendly features, these models represent a blend of innovation and practicality.

The Poulan 952802326 is particularly noted for its compact design, which makes it a favorite among homeowners and professionals alike. It boasts a robust 18-inch bar and chain, allowing for efficient cutting of medium-sized trees and limbs. The 40cc two-stroke engine provides ample power for demanding tasks while maintaining a lightweight construction that minimizes fatigue during extended use. One of its standout features is the Easy Start technology, which reduces the effort required to start the engine, making it accessible for users of all skill levels.

The SM4218AVX model is engineered for versatility, equipped with a 42cc engine that balances power and efficiency. Its low-vibration design enhances user comfort, significantly reducing strain during operations. This chainsaw also features an automatic oiling system that ensures optimal lubrication of the bar and chain, extending their lifespan and reducing maintenance efforts. The Quick-Release air filter allows for easy access, promoting better engine performance and longevity.

The Poulan 545167697 represents a leap in technology with its advanced safety features. It includes a chain brake that activates in case of kickback, ensuring the user's protection. Additionally, the anti-vibration system adds to the overall safety, making the chainsaw easier to control and maneuver. Its lightweight nature does not compromise its rugged durability, making it ideal for both professional logging and home landscaping projects.

Each of these Poulan models embodies a commitment to quality and performance. With user-friendly controls, efficient fuel consumption, and advanced safety mechanisms, they cater to a wide range of users, from casual homeowners to seasoned professionals. Their design reflects a focus on not only power and efficiency but also on user comfort and safety, ensuring that even demanding tasks can be completed with confidence and ease. Whether tackling heavy-duty forestry projects or simple backyard maintenance, the Poulan 952802326, SM4218AVX, and 545167697 stand out as reliable companions in outdoor power equipment.
Top Page Image Contents