Poulan 191697 Transaxle Motion Control LE- VER Neutral Adjustment, Front Wheel TOE-IN/CAMBER

Page 29

TRANSAXLE MOTION CONTROL LE- VER NEUTRAL ADJUSTMENT

The motion control lever has been preset at the factory and adjustment should not be necessary.

1.Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

2.Start engine and move motion con- trol lever until tractor does not move forward or backward.

3.Hold motion control lever in that posi- tion and turn engine off.

4.While holding motion control lever in place, loosen the adjustment bolt.

5.Move motion control lever to the neu- tral (N) (lock gate) position.

6.Tighten adjustment bolt securely. NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

1.Loosen the adjustment bolt.

2.Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

3.Tighten adjustment bolt securely.

4.Start engine and test.

5.If tractor still creeps, repeat above steps until satisfied.

Motion Control Lever

 

Neutral

02239

Lock

Adjustment Bolt

Gate

TRANSMISSION REMOVAL/

REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before op- erating the tractor. See “PURGE TRANS- MISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact our authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealant from an authorized service center/department. Tire sealant also pre- vents tire dry rot and corrosion.

Washers

Retaining

Ring

Axle

Cover

00663

Square Key

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BAT- TERY

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

29

Image 29
Contents Model NO. CO24H48STA Warranty Table of ContentsII. Slope Operation Safety RulesGeneral Operation Do not IV. ServiceIII. Children Safety Rules API-SF-SJ Product SpecificationsCustomer Responsibilities Gauge Wheels Nose Roller Unassembled PartsTools Required for Assembly ASSEMBLY/PRE-OPERATIONTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat Assemble Gauge Wheels to Mower Deck To Attach Nose RollerInstall Mower and Drive Belt Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor To USE Choke Control HOW to USE Your TractorTo Operate on Hills To Adjust Gauge WheelsTo Operate Mower To Transport Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission To Start EngineMowing Tips Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Transaxle Cooling EngineTransaxle Pump Fluid BeltsAIR Filter CleaningTo Remove Mower Service and AdjustmentsTo Install Mower SIDE-TO-SIDE Adjustment To Level Mower HousingMower Drive Belt Removal Mower Drive Belt InstallationTo Replace Mower Drive Belt To Replace Mower Blade SEC- Ondary Drive Belt Install NEW Mower Blade Secondary Drive BeltRemove Mower Drive Belt Remove Mower Blade Secondary Drive BeltTo Adjust Brake To Check and Adjust BrakeBelt Installation To Check BrakeTransmission Removal Replacement Transaxle Motion Control LE- VER Neutral AdjustmentTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable Replacing BatteryTo Adjust Carburetor To Replace Headlight BulbOther BatteryStorage Problem Cause Correction Troubleshooting ChartExcessive Headlights not Suggested Guide for Sighting Slopes for Safe Operation