Poulan 194563 manual Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place motion control lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 14)

Mower will be easier to remove from the right side of trac- tor.

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Remove small retainer spring, and remove clutch spring off pulley bolt.

•Remove large retainer spring, slide collar off and push housing guide out of bracket.

•Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONTLINKSANDHOOKTHECLUTCHSPRINGINTOSQUARE HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 14)

•Raise attachment lift lever to its highest position.

•Slide mower under tractor with deflector shield to right side of tractor.

•Lower lift lever to its lowest position.

•Connect front links to mower deck and secure with retainer springs..

•Connect suspension arms to rear deck brackets and secure with retainer springs.

•Connect anti-swaybar to chassis bracket and secure with retainer spring.

•Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

•Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

•Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

 

SMALL RETAINER SPRING

 

 

 

 

CLUTCH SPRING

 

 

 

 

FLAT WASHER

 

 

SQUARE HOLE

SMALL RETAINER SPRING

 

SUSPENSION

ENGINE PULLEY

 

 

 

ARMS

 

 

 

 

CLUTCH SPRING

 

 

 

 

 

 

 

FRONT LINK

RETAINER SPRING

 

 

 

 

ANTI-SWAY BAR

 

 

 

 

 

 

 

 

RETAINER SPRINGS

COLLAR

 

 

 

(BOTH SIDES)

HOUSING GUIDE

LARGE RETAINER

 

 

 

SPRING

BRACKET

 

DEFLECTOR SHIELD

 

 

 

 

 

 

 

FIG. 14

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Always Wear EYE Protection During Operation PB185H42LTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust BrakeFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

194563 specifications

The Poulan 194563 is a powerful and efficient chainsaw designed for both professional and personal use. Renowned for its reliability and performance, this model stands out in the market due to its innovative features and robust engineering.

One of the key highlights of the Poulan 194563 is its engine. Equipped with a high-performance 42cc gas engine, it delivers ample power for cutting through various types of wood, including hardwoods, making it ideal for landscaping, tree trimming, and firewood cutting. The engine is designed with efficiency in mind, providing a commendable horsepower to weight ratio which enhances maneuverability and reduces user fatigue during extended use.

The chainsaw features an easy-to-start system, which minimizes the frustration often associated with starting gas-powered tools. This is complemented by an automatic oiling system that ensures the chain remains lubricated during operation, prolonging the lifespan of the chain while maintaining optimal performance levels.

The Poulan 194563 also includes a 16-inch bar and chain setup. This size strikes a perfect balance, allowing users to tackle medium to large cutting tasks without becoming unwieldy. The low-kickback chain is designed to provide added safety while cutting, making it more user-friendly for both novices and experienced users alike.

In terms of ergonomics, the Poulan 194563 is equipped with a comfortable grip handle that allows for confident and controlled operation. The anti-vibration technology incorporated into its design helps minimize vibrations felt during use, promoting a more comfortable and less fatiguing experience over time.

Safety features are also a priority in the design of the Poulan 194563. It includes a chain brake that engages automatically in case of kickback, further protecting the user. The transparent fuel and oil tanks allow for easy monitoring, ensuring that operators are aware of fuel levels at all times.

Overall, the Poulan 194563 brings together an impressive combination of power, safety, and user-friendly technology. Whether you're a professional needing reliable equipment for daily tasks or a homeowner maintaining your yard, the Poulan 194563 is a commendable choice that promises performance and durability for a variety of cutting needs.
Top Page Image Contents