Poulan 194563 manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel ALIGN- Ment

Page 22

SERVICE AND ADJUSTMENTS

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ADJUSTMENT

BOLT

FIG. 22

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 23)

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 23

TO START ENGINE WITH A WEAK BATTERY (See Fig. 24)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

FIG. 24

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PB185H42LT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Steering Wheel Seat Unassembled PartsSlope Sheet To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceLubrication Chart Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Adjust Brake To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

194563 specifications

The Poulan 194563 is a powerful and efficient chainsaw designed for both professional and personal use. Renowned for its reliability and performance, this model stands out in the market due to its innovative features and robust engineering.

One of the key highlights of the Poulan 194563 is its engine. Equipped with a high-performance 42cc gas engine, it delivers ample power for cutting through various types of wood, including hardwoods, making it ideal for landscaping, tree trimming, and firewood cutting. The engine is designed with efficiency in mind, providing a commendable horsepower to weight ratio which enhances maneuverability and reduces user fatigue during extended use.

The chainsaw features an easy-to-start system, which minimizes the frustration often associated with starting gas-powered tools. This is complemented by an automatic oiling system that ensures the chain remains lubricated during operation, prolonging the lifespan of the chain while maintaining optimal performance levels.

The Poulan 194563 also includes a 16-inch bar and chain setup. This size strikes a perfect balance, allowing users to tackle medium to large cutting tasks without becoming unwieldy. The low-kickback chain is designed to provide added safety while cutting, making it more user-friendly for both novices and experienced users alike.

In terms of ergonomics, the Poulan 194563 is equipped with a comfortable grip handle that allows for confident and controlled operation. The anti-vibration technology incorporated into its design helps minimize vibrations felt during use, promoting a more comfortable and less fatiguing experience over time.

Safety features are also a priority in the design of the Poulan 194563. It includes a chain brake that engages automatically in case of kickback, further protecting the user. The transparent fuel and oil tanks allow for easy monitoring, ensuring that operators are aware of fuel levels at all times.

Overall, the Poulan 194563 brings together an impressive combination of power, safety, and user-friendly technology. Whether you're a professional needing reliable equipment for daily tasks or a homeowner maintaining your yard, the Poulan 194563 is a commendable choice that promises performance and durability for a variety of cutting needs.
Top Page Image Contents