Poulan 194598 manual Tractor, Blade Removal See Fig, To Sharpen Blade See Fig

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

828

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 8)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS HEATTREATED.IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN IN THE REPAIR PARTS.

 

 

MANDREL

TRAILING

BLADE

ASSEMBLY

EDGE UP

 

 

CENTER

 

 

 

 

HOLE

FLAT WASHER

 

 

LOCK WASHER

 

STAR

BLADE BOLT

FIG. 8

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PD15538LT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Battery EngineBelts Transaxle CoolingCleaning Clean AIR ScreenAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

194598 specifications

The Poulan 194598 is a noteworthy entry in the realm of outdoor power equipment, particularly tailored for lawn care. This product, recognized for its reliability and functionality, is primarily a chainsaw that caters to both amateur gardeners and professionals alike. As part of Poulan’s commitment to innovation and quality, the 194598 model embodies several features and technologies designed to enhance the user experience.

At its core, the Poulan 194598 boasts a robust engine that provides ample power for cutting through various types of wood, whether it's trimming branches or felling small trees. This chainsaw typically comes equipped with a powerful two-cycle engine, delivering streamlined performance while ensuring efficiency. The engine is designed for easy starting, minimizing the hassle often encountered with starting similar devices.

One of the standout features of the Poulan 194598 is its lightweight design. Weighing significantly less than many competing models, this chainsaw allows for extended use without leading to user fatigue. The ergonomic handle contributes to a comfortable grip, which is essential during prolonged operations. This thoughtful design is a hallmark of Poulan products, reflecting their understanding of user ergonomics.

In terms of safety, the Poulan 194598 is equipped with several essential safety features. These include a chain brake, which can be activated in instances of kickback, significantly reducing the risk of injury. Additionally, an integrated chain tensioning system allows users to make adjustments quickly and easily, promoting safe and efficient operation.

Another notable attribute is the chainsaw's low vibration technology. This feature not only enhances user comfort but also contributes to a more stable performance. Less vibration translates to better control and precision during cutting tasks, making the Poulan 194598 an appealing option for those who value accuracy in their work.

Maintenance is also straightforward with the Poulan 194598, as it typically offers easy access to the air filter and spark plug, allowing for routine upkeep to be performed without excessive effort. This aspect appeals to both casual users and more serious professionals who appreciate devices that require less downtime.

In summary, the Poulan 194598 is a versatile, user-friendly chainsaw that combines power, safety, and comfort. Its thoughtful design, augmented by technologies that minimize vibration and enhance safety, make it an excellent choice for anyone looking to tackle outdoor cutting tasks efficiently and reliably. With its robust features and characteristics, the Poulan 194598 stands as a commendable tool for both homeowners and landscape professionals.
Top Page Image Contents