Poulan 194598 Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig, Front Wheel TOE-IN/CAMBER

Page 22

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 21)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

NEUTRAL

LOCK GATE

GEARSHIFT LEVER

ADJUSTMENT

BOLT

FIG. 21

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 22)

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 22

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

FIG. 23

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PD15538LT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

194598 specifications

The Poulan 194598 is a noteworthy entry in the realm of outdoor power equipment, particularly tailored for lawn care. This product, recognized for its reliability and functionality, is primarily a chainsaw that caters to both amateur gardeners and professionals alike. As part of Poulan’s commitment to innovation and quality, the 194598 model embodies several features and technologies designed to enhance the user experience.

At its core, the Poulan 194598 boasts a robust engine that provides ample power for cutting through various types of wood, whether it's trimming branches or felling small trees. This chainsaw typically comes equipped with a powerful two-cycle engine, delivering streamlined performance while ensuring efficiency. The engine is designed for easy starting, minimizing the hassle often encountered with starting similar devices.

One of the standout features of the Poulan 194598 is its lightweight design. Weighing significantly less than many competing models, this chainsaw allows for extended use without leading to user fatigue. The ergonomic handle contributes to a comfortable grip, which is essential during prolonged operations. This thoughtful design is a hallmark of Poulan products, reflecting their understanding of user ergonomics.

In terms of safety, the Poulan 194598 is equipped with several essential safety features. These include a chain brake, which can be activated in instances of kickback, significantly reducing the risk of injury. Additionally, an integrated chain tensioning system allows users to make adjustments quickly and easily, promoting safe and efficient operation.

Another notable attribute is the chainsaw's low vibration technology. This feature not only enhances user comfort but also contributes to a more stable performance. Less vibration translates to better control and precision during cutting tasks, making the Poulan 194598 an appealing option for those who value accuracy in their work.

Maintenance is also straightforward with the Poulan 194598, as it typically offers easy access to the air filter and spark plug, allowing for routine upkeep to be performed without excessive effort. This aspect appeals to both casual users and more serious professionals who appreciate devices that require less downtime.

In summary, the Poulan 194598 is a versatile, user-friendly chainsaw that combines power, safety, and comfort. Its thoughtful design, augmented by technologies that minimize vibration and enhance safety, make it an excellent choice for anyone looking to tackle outdoor cutting tasks efficiently and reliably. With its robust features and characteristics, the Poulan 194598 stands as a commendable tool for both homeowners and landscape professionals.
Top Page Image Contents