Poulan 96046001400 To Move Forward and Backward See Fig, To Adjust Mower Cutting Height See Fig

Page 11

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 8)

The direction and speed of movement is controlled by the gearshift lever (J).

J

Fig. 8

1.Start tractor with clutch/brake pedal depressed and gearshift lever in neutral position.

2.Move gearshift lever to desired position.

3.Slowly release clutch/brake pedal to start movement.

IMPORTANT: Bring tractor to a complete stop before shifting or changing gears. Failure to do so will shorten the useful life of your transaxle.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 9)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 9

Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

REVERSE OPERATION SYSTEM (ROS) (See Fig. 11)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

Only use if you are certain no children or other bystanders will enter the mowing area.

Depress clutch/brake pedal all the way down and hold.

With engine running, turn ignition key counterclockwise to ROS "ON" position.

Look down and behind before backing.

Move gear shift lever to reverse (R) position and slowly release clutch/brake pedal to start movement.

When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

 

 

 

 

 

 

 

 

 

 

02828

ROS "ON"

ENGINE "ON" POSITION

POSITION

(NORMAL OPERATING)

 

 

 

 

 

 

Fig. 10

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

Start mower blades by engaging attachment clutch control.

11

Image 11
Contents PXT12530 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly ToremovetractorfromcartonCheck Brake System Install Seat See FigOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged To SET Parking Brake See FigReverse Operation System ROS See Fig To Adjust Mower Cutting Height See FigUsing the Reverse Operation System To Move Forward and Backward See FigBefore Starting the Engine To Start Engine See Fig Mowing TipsSchedule MaintenanceMaintenance General RecommendationsBlade Removal See Fig BatteryTractor Blade CareLubrication Transaxle MaintenanceEngine BeltsMuffler Clean AIR ScreenCleaning AIR FilterTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Raise attachment lift lever to highest position To Level Mower Visual SIDE-TO-SIDE Adjustment See FigTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Remove Wheel See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigInterlocks and Relays To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsExcessive Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationLimited Warranty