Poulan XT22H42YT, 404378 manual To Replace Mower Drive Belt See Fig, To Check Brake

Page 21

SERVICE AND ADJUSTMENTS

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

TO REPLACE MOWER DRIVE BELT (See Fig. 26)

MOWER DRIVE BELT REMOVAL

Park tractor on a level surface. Engage parking brake.

Lower attachment lift lever to its lowest position.

Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

Remove belt from electric clutch pulley (M), both man- drel pulleys (R) and all idler pulleys (S).

MOWER DRIVE BELT INSTALLATION

Install belt around all mandrel pulleys (R) and around idler pulleys (S) as shown.

Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

Raise attachment lift lever to highest position.

S

M

R

R

FIG. 26

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

Place gear shift lever in neutral (N) position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

21

TO REPLACE MOTION DRIVE BELT (See Fig. 27)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

Remove belt from stationary idler (A) and clutching idler (B).

Remove belt from centerspan idler (C).

Pull belt slack toward rear of tractor. Remove belt upwards from transaxle input pulley (D).

Remove belt downward from engine pulley (E).

Slide belt toward rear of tractor, off the steering plate

(F) and remove from tractor.

BELT INSTALLATION -

Install new belt from tractor rear to front, over the steer- ing plate (F) and above clutch brake pedal shaft (G).

Pull belt toward front of tractor and roll belt onto engine pulley (E).

Pull belt toward rear of tractor. Carefully work belt down around transaxle input pulley (D). Be sure belt is inside the belt keeper.

Install belt on centerspan idler (C).

Install belt through stationary idler (A) and clutching idler (B).

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

E

F

A

B G

C

D

FIG. 27

Image 21
Contents Always Wear EYE Protection During Operation XT22H42YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Reverse Operation System ROS on Position Know Your TractorTo SET Parking BRAKESee Fig HOW to USE Your TractorStopping To USE Throttle Control D See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To Operate MowerBefore Starting the Engine Service REMINDER/HOUR MeterReverse Operation System ROS To Operate on HillsTo Start Engine See Fig ADD GasolinePurge Transmission Automatic Transmission Warm UPMowing Tips Before Each USE MaintenanceTractor BatteryBrake Operation TiresEngine Engine OIL Filter CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Figs To Level Mower To Replace Mower Drive Belt See Fig To Check BrakeTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationPage Parts and Service