Poulan 404973 manual To USE Cruise Control -J See Fig, To Adjust Mower Cutting Height See Fig

Page 13

OPERATION

J

K

L

FIG. 15

TO USE CRUISE CONTROL -J (See Fig. 15)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 16)

The position of the attachment lift lever (A) determines the cutting height.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the fi rst cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 17)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a fl at level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

A

FIG. 16

•Put attachment lift lever in desired cutting height slot.

•Slide pointer tab (T) to desired cutting height as a reminder for next time you mow.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

FIG.17

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield (S) in place.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Always Wear EYE Protection During Operation PBGT26H54Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Mower Mower Front Wheel Unassembled PartsSlope Sheet Keys Tools Required for Assembly AssemblyTo Remove Tractor from Carton Unpack CartonAssemble Front Wheel to Mower See Fig Install Mower and Drive Belt7/16 Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To USE Cruise Control -J See FigUsing the Reverse Operation System Service REMINDER/HOUR MeterReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Lubrication Chart MaintenanceTractor BatteryBrake Operation TiresEngine Engine OIL Filter CleaningMuffler Spark PlugsTo Install Mower Service and AdjustmentsTractor See Fig To Remove MowerTurn nut right Turn nut left To raise mower To Check Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt Front Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Page Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

404973 specifications

The Poulan 404973 is a powerful and versatile chainsaw designed for both amateur and professional users who require reliable performance for various cutting tasks. Known for its robust build and user-friendly features, the 404973 has become a favored choice among homeowners and landscapers alike.

One of the standout features of the Poulan 404973 is its engine. Powered by a 42cc, two-stroke engine, this chainsaw offers a commendable balance of power and efficiency. This engine delivers ample torque for cutting through dense wood, making it suitable for felling trees, pruning branches, and cutting firewood. The inclusion of a primer bulb allows for quick starts, reducing user frustration during the initial ignition phase.

The design of the Poulan 404973 emphasizes user comfort and control. It is equipped with an ergonomic handle that minimizes vibrations, allowing for extended use without excessive fatigue. Additionally, the chainsaw features a lightweight construction, which further enhances portability and ease of handling. This combination of comfort and control helps users maintain precision during their cutting tasks.

Safety is a key consideration in the design of the Poulan 404973. It comes equipped with a chain brake that protects users from kickback incidents, a common hazard in chainsaw operation. This feature automatically stops the chain in the event of sudden movements or loss of control. Moreover, the chainsaw also includes a safety throttle lock, ensuring that the chain does not operate unexpectedly while starting.

Another impressive aspect of the Poulan 404973 is its automatic oiling system. This technology ensures that the chain remains well-lubricated during use, reducing friction and prolonging the lifespan of both the chain and the guide bar. The oil reservoir is transparent, allowing users to monitor oil levels easily and prevent any interruptions during operation.

Lastly, maintaining the chainsaw is a straightforward process, thanks to features like tool-less chain adjustment and easy access to the air filter. This design simplifies upkeep, enabling users to keep their equipment in optimal condition without requiring extensive technical knowledge.

Overall, the Poulan 404973 stands out as a reliable and functional chainsaw with a blend of power, safety, and user-friendly features that cater to a wide range of cutting needs. Whether for domestic or light commercial use, this chainsaw proves to be a valuable addition to any toolkit.
Top Page Image Contents