Poulan 404973 To Adjust Throttle Control Cable, To Replace Headlight Bulb, Interlocks and Relays

Page 25

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig. 34)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected fi rst to prevent spark- ing from accidental grounding.

•Lift hood to raised position.

•Disconnect BLACK battery cable (A) then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable (B) to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover (C) over terminal.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close hood.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 35)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

02141

C

Positive B (Red) Cable

ANegative (Black) Cable

FIG. 35

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

02954

FIG. 34

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Always Wear EYE Protection During Operation PBGT26H54Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Mower Mower Front Wheel Unassembled PartsSlope Sheet Keys Tools Required for Assembly AssemblyTo Remove Tractor from Carton Unpack CartonAssemble Front Wheel to Mower See Fig Install Mower and Drive Belt7/16 Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To USE Cruise Control -J See FigUsing the Reverse Operation System Service REMINDER/HOUR MeterReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Lubrication Chart MaintenanceTractor BatteryBrake Operation TiresEngine Engine OIL Filter CleaningMuffler Spark PlugsTo Install Mower Service and AdjustmentsTractor See Fig To Remove MowerTurn nut right Turn nut left To raise mower To Check Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt Front Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Page Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

404973 specifications

The Poulan 404973 is a powerful and versatile chainsaw designed for both amateur and professional users who require reliable performance for various cutting tasks. Known for its robust build and user-friendly features, the 404973 has become a favored choice among homeowners and landscapers alike.

One of the standout features of the Poulan 404973 is its engine. Powered by a 42cc, two-stroke engine, this chainsaw offers a commendable balance of power and efficiency. This engine delivers ample torque for cutting through dense wood, making it suitable for felling trees, pruning branches, and cutting firewood. The inclusion of a primer bulb allows for quick starts, reducing user frustration during the initial ignition phase.

The design of the Poulan 404973 emphasizes user comfort and control. It is equipped with an ergonomic handle that minimizes vibrations, allowing for extended use without excessive fatigue. Additionally, the chainsaw features a lightweight construction, which further enhances portability and ease of handling. This combination of comfort and control helps users maintain precision during their cutting tasks.

Safety is a key consideration in the design of the Poulan 404973. It comes equipped with a chain brake that protects users from kickback incidents, a common hazard in chainsaw operation. This feature automatically stops the chain in the event of sudden movements or loss of control. Moreover, the chainsaw also includes a safety throttle lock, ensuring that the chain does not operate unexpectedly while starting.

Another impressive aspect of the Poulan 404973 is its automatic oiling system. This technology ensures that the chain remains well-lubricated during use, reducing friction and prolonging the lifespan of both the chain and the guide bar. The oil reservoir is transparent, allowing users to monitor oil levels easily and prevent any interruptions during operation.

Lastly, maintaining the chainsaw is a straightforward process, thanks to features like tool-less chain adjustment and easy access to the air filter. This design simplifies upkeep, enabling users to keep their equipment in optimal condition without requiring extensive technical knowledge.

Overall, the Poulan 404973 stands out as a reliable and functional chainsaw with a blend of power, safety, and user-friendly features that cater to a wide range of cutting needs. Whether for domestic or light commercial use, this chainsaw proves to be a valuable addition to any toolkit.
Top Page Image Contents