Poulan 96042003400, 411188 manual Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig

Page 23

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 26)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 27

TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)

GEARSHIFT LEVER

NEUTRAL LOCK GATE

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

ADJUSTMENT

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and

corrosion.23

FIG. 28

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PB19542LT II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Carton AssemblyTools Required for Assembly To Remove Tractor fromCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS Before Starting the Engine Mowing Tips General Recommendations MaintenanceTo Sharpen Blade See Fig TractorBlade Removal See Fig Transaxle Cooling BatteryEngine BeltsCleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Precision SIDE-TO-SIDE AdjustmentTo Check Brake Belt InstallationTo Replace Mower Drive Belt See Fig To Replace Motion Belt Drive See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Tractor - Model Number PB19542LT 96042003400, Product no 42 SchematicElectrical KEY Part Description 162 DriveRepair Parts Chassis 194263 Drawbar Wheels and Tires DecalsSteering Engine Engine Power Rating Information Mower Deck Repair Parts Seat Mower Lift Service Notes Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationPolicy

96042003400, 411188 specifications

The Poulan 411188,96042003400 is a high-performance chainsaw designed for both professional and home users who require durability and efficiency in their cutting tasks. This robust tool is engineered to tackle a variety of jobs, from felling trees to pruning branches, making it an essential item for outdoor maintenance and forestry work.

One of the main features of the Poulan 411188 is its potent engine. It is equipped with a powerful 40cc, gas-powered motor that delivers an impressive amount of torque and cutting speed. This power allows users to cut through different types of wood with ease, whether they are working on hardwoods or softer varieties. The engine is designed for optimal fuel efficiency, helping to reduce the frequency of refueling during extended use.

Another standout characteristic of this chainsaw is its lightweight and ergonomic design. Weighing just under 10 pounds, it is user-friendly and easy to maneuver, which is particularly beneficial for extended cutting tasks. The chainsaw also features an anti-vibration handle that minimizes fatigue, allowing for improved control and comfort during operation. This design consideration ensures that the user can maintain accuracy while reducing strain on the hands and arms.

The Poulan 411188 incorporates advanced safety features that make it a reliable choice for both novice and experienced users. A low-kickback chain helps to prevent unexpected jolts during operation, while a chain brake provides an additional layer of safety by stopping the chain’s movement immediately in case of kickback. These features are crucial for preventing accidents and enhancing user confidence.

In terms of technology, the chainsaw features an easy-start system that reduces the effort required to start the engine. This is especially beneficial for users who may struggle with traditional pull-start mechanisms. The transparent fuel tank allows users to easily monitor fuel levels, preventing interruptions during work.

Overall, the Poulan 411188,96042003400 is a versatile and durable chainsaw that offers a blend of power, efficiency, and safety features. Whether for yard work, on the job site, or in a backyard setting, this chainsaw meets the needs of a diverse range of users. Its combination of user-friendly design and robust performance makes it an ideal option for anyone looking to tackle cutting tasks effectively.
Top Page Image Contents