Poulan 184523, 954569561 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

FIG. 28

TERMINAL

KEPS

NUT

COVER

 

HEX

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

FIG. 29

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 30)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 30

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 31)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

 

GOVERNOR

GOVERNOR

 

CONTROL LEVER

 

CONTROL PLATE

 

 

HOLES “A”

CLAMP

THROTTLE

 

SCREW

CABLE

FIG. 31

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - dam- age may result.

IMPORTANT:NEVERTAMPERWITHTHEENGINEGOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACTYOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. PO18H42STA II. Slope Operation IV. ServiceSafe Operation Practices for Ride-On Mowers General OperationSafety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat KeyTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Operate Mower See FigTo Operate on Hills To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsGeneral Recommendations MaintenanceLubrication Chart Service DatesTractor Engine Spark Plugs CleaningEngine OIL Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check Brake Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Replacing Battery See FigsTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PO18H42STA, Product no 56 SchematicTractor - Model Number PO18H42STA, Product no 56 Electrical KEY Part NO. NO. Description Chassis-pl.ltstlt50 KEY Part Description Tractor - Model Number PO18H42STA, Product no 56 Drive Repair Parts 6867 8546 856 KEY Part NO. NO. Description Tractor - Model Number PO18H42STA, Product no 56 Engine Repair Parts KEY Part Description Wheels & Tires Tractor - Model Number PO18H42STA, Product no 56 DecalsTractor - Model Number PO18H42STA, Product no 56 Mower Lift Repair Parts Tractor - Model Number PO18H42STA, Product no 56 Mower Deck 165892 Service Notes Service Notes Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

184523, 954569561 specifications

The Poulan 954569561,184523 is a robust and highly efficient lawn mower designed to meet the demands of both amateur gardeners and professional landscapers. Featuring advanced engineering and a user-friendly design, this mower offers a range of features that ensure seamless operation and exceptional performance.

One of the standout features of the Poulan 954569561,184523 is its powerful engine. Equipped with a reliable 4-cycle engine, this mower delivers consistent power that allows it to tackle various types of grass and terrain with ease. The efficient fuel consumption means longer mowing sessions without the frequent need for refueling, making it ideal for larger lawns.

Another key characteristic of the Poulan lawn mower is its cutting deck, which measures 21 inches. This size strikes a perfect balance between maneuverability and coverage, allowing users to navigate tight spaces while still efficiently cutting larger areas. The cutting height is easily adjustable, giving users the ability to customize the length of the grass according to their preferences and specific lawn care needs.

Technology plays a significant role in enhancing the overall user experience of the Poulan 954569561,184523. The mower features an ergonomic handle design that reduces strain during operation, making it comfortable for extended periods of use. Additionally, the mower is equipped with a reliable start system, ensuring that it fires up quickly and efficiently, saving users time and frustration.

Durability is another important aspect of this mower's design. Built with high-quality materials, the Poulan 954569561,184523 is engineered to withstand the rigors of lawn care season after season. Its sturdy construction contributes to its longevity, ensuring that users can rely on this mower for many years.

Maintenance is also straightforward, with accessible components designed for easy servicing. Users can quickly change spark plugs, filters, and oil, keeping the mower in peak condition without requiring a lot of mechanical expertise.

In summary, the Poulan 954569561,184523 is a powerful and efficient lawn mower that combines advanced technology, user-centric features, and robust durability. Its thoughtful design elements cater to both novice and experienced users, making it a versatile choice for maintaining a pristine lawn. Whether for residential or professional use, this mower stands out as a reliable tool for any landscaping task.
Top Page Image Contents