Poulan 954569561, 184523 manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(2)

7/16" wrenches

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten se- curely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

 

INSERT

 

1/2 LOCK WASHER

 

LARGE FLAT

 

WASHER

STEERING

 

WHEEL

 

 

STEERING

 

BOOT

 

TABS

ADAPTER

EXTENSION SHAFT

 

 

1/4 HEX BOLT

1/4 LOCKNUT

 

LOWER

 

STEERING

 

SHAFT

 

 

TAB

 

SLOTS

FIG. 1

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. PO18H42STA General Operation IV. ServiceSafe Operation Practices for Ride-On Mowers II. Slope OperationSafety Rules Table of Contents Key Unassembled PartsSteering Wheel Seat Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Operate on HillsTo Transport See Figs ADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionService Dates MaintenanceLubrication Chart General RecommendationsTractor Engine Muffler CleaningEngine OIL Filter Spark PlugsTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Check BrakeReplacing Battery See Figs Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO18H42STA, Product no 56Tractor - Model Number PO18H42STA, Product no 56 Electrical KEY Part NO. NO. Description Chassis-pl.ltstlt50 KEY Part Description Tractor - Model Number PO18H42STA, Product no 56 Drive Repair Parts 6867 8546 856 KEY Part NO. NO. Description Tractor - Model Number PO18H42STA, Product no 56 Engine Repair Parts KEY Part Description Tractor - Model Number PO18H42STA, Product no 56 Decals Wheels & TiresTractor - Model Number PO18H42STA, Product no 56 Mower Lift Repair Parts Tractor - Model Number PO18H42STA, Product no 56 Mower Deck 165892 Service Notes Service Notes Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

184523, 954569561 specifications

The Poulan 954569561,184523 is a robust and highly efficient lawn mower designed to meet the demands of both amateur gardeners and professional landscapers. Featuring advanced engineering and a user-friendly design, this mower offers a range of features that ensure seamless operation and exceptional performance.

One of the standout features of the Poulan 954569561,184523 is its powerful engine. Equipped with a reliable 4-cycle engine, this mower delivers consistent power that allows it to tackle various types of grass and terrain with ease. The efficient fuel consumption means longer mowing sessions without the frequent need for refueling, making it ideal for larger lawns.

Another key characteristic of the Poulan lawn mower is its cutting deck, which measures 21 inches. This size strikes a perfect balance between maneuverability and coverage, allowing users to navigate tight spaces while still efficiently cutting larger areas. The cutting height is easily adjustable, giving users the ability to customize the length of the grass according to their preferences and specific lawn care needs.

Technology plays a significant role in enhancing the overall user experience of the Poulan 954569561,184523. The mower features an ergonomic handle design that reduces strain during operation, making it comfortable for extended periods of use. Additionally, the mower is equipped with a reliable start system, ensuring that it fires up quickly and efficiently, saving users time and frustration.

Durability is another important aspect of this mower's design. Built with high-quality materials, the Poulan 954569561,184523 is engineered to withstand the rigors of lawn care season after season. Its sturdy construction contributes to its longevity, ensuring that users can rely on this mower for many years.

Maintenance is also straightforward, with accessible components designed for easy servicing. Users can quickly change spark plugs, filters, and oil, keeping the mower in peak condition without requiring a lot of mechanical expertise.

In summary, the Poulan 954569561,184523 is a powerful and efficient lawn mower that combines advanced technology, user-centric features, and robust durability. Its thoughtful design elements cater to both novice and experienced users, making it a versatile choice for maintaining a pristine lawn. Whether for residential or professional use, this mower stands out as a reliable tool for any landscaping task.
Top Page Image Contents