Poulan DB24H48YT manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

•Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop retainer springs between the plate assembly and mower brackets.

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•Engage belt tension rod by pushing rod into locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

00598

GROUND

A

GROUND LINE

A

 

FIG. 19

SUSPENSION

ARM

01553

LIFT LINK

ADJUSTMENT NUT

FIG. 20

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front plate links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns.The two front links must remain equal in length.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

BLADE

02548

“B”“B”

FIG. 21

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Always Wear EYE Protection During Operation DB24H48YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Install Mower and Drive Belt See Figs To Attach Nose Roller See FigAssemble Gauge Wheels to Mower Deck See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigReverse Operation System ROS To Operate on HillsTo Transport See Figs Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Check Operator Presence SystemEngine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt Mower Drive Belt InstallationTo Replace Mower Blade Secondary Drive Belt See Fig To Check and Adjust Brake See FigBelt Installation Transaxle Motion Control Lever Neutral Adjustment See FigTo Replace Motion Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace FuseOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

DB24H48YT specifications

The Poulan DB24H48YT is a versatile and robust lawn tractor designed to meet the diverse needs of homeowners managing their lawns and gardens. This model stands out for its powerful performance and various features that make yard work less tedious and more efficient.

One of the key characteristics of the Poulan DB24H48YT is its potent 24-horsepower Briggs & Stratton engine. This reliable engine delivers plenty of power for tackling both flat and uneven terrains, ensuring that cutting through thick grass is no challenge. The engine is paired with a hydrostatic transmission, providing smooth and effortless operation, with the ability to change speed seamlessly during mowing tasks without the need for manual gear shifting.

Featuring a 48-inch cutting deck, the Poulan DB24H48YT offers a wider cutting path, reducing the number of passes needed to achieve a well-manicured lawn. The cutting height is adjustable, allowing users to choose optimal grass height according to their preferences or seasonal requirements. With its three-blade system, this lawn tractor delivers an even and precise cut, enhancing the overall aesthetic of lawns.

Another noteworthy feature of the Poulan DB24H48YT is the inclusion of an ergonomic control system, designed for user comfort. The soft-touch steering wheel provides excellent grip, while the adjustable seat ensures that operators can find their most comfortable position during lengthy mowing sessions. Easy access to the key controls facilitates quick adjustments while maneuvering around obstacles in the yard.

Equipped with exceptional maneuverability thanks to the tight turning radius, this model can navigate around flower beds, trees, and other landscaping features with ease. The Poulan DB24H48YT also supports various attachments, expanding its functionality for tasks beyond mowing, such as mulching, hauling, or snow removal.

Overall, the Poulan DB24H48YT embodies a well-rounded combination of power, durability, and versatility, making it an excellent choice for homeowners seeking an efficient solution for lawn care. Its blend of advanced features and technological innovations ensures that it provides reliable performance year after year, helping users maintain pristine lawns with ease.
Top Page Image Contents