Poulan HD1842 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

 

FIG. 24

TERMINAL

KEPS NUT

COVER

 

HEX

BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 25

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 26)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

01536

FIG. 26

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Always Wear EYE Protection During Operation HD1842II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport To Operate Mower See FigTo Operate on Hills Reverse Operation System ROSTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Transaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust BrakeTo Attach Jumper Cables To Adjust Steering Wheel ALIGN- MentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

HD1842 specifications

The Poulan HD1842 is a robust and reliable riding lawn mower designed for homeowners who require efficiency and ease of use while maintaining their lawns. This machine features a powerful engine paired with a 42-inch cutting deck, making it an ideal choice for medium to large-sized yards.

At the heart of the Poulan HD1842 is a reliable 18.5 HP Briggs & Stratton engine, known for its durability and performance. This engine provides ample power to tackle even the toughest grass, ensuring a smooth and effective cutting experience. The engine is designed for easy starting and requires minimal maintenance, making it suitable for users looking for convenience.

One of the standout features of the HD1842 is its cutting deck. The 42-inch deck is equipped with three high-performance blades that provide a clean and even cut, allowing for professional-looking results every time. The deck height can be easily adjusted to six different positions, ranging from 1.5 to 4 inches, giving users the flexibility to choose the perfect height for their grass type and desired look.

Another significant technology integrated into the Poulan HD1842 is the hydrostatic transmission. This feature allows for smooth and effortless speed adjustments while maintaining full control over the mower's movement. Users can easily navigate around obstacles and tight corners without the need to pause and change gears, enhancing the overall mowing experience.

Comfort is also a priority with the HD1842. The mower features a spacious and comfortable seat that can be adjusted to accommodate different user heights. Additionally, the steering wheel is ergonomically designed, providing a better grip and reducing operator fatigue even during extended mowing sessions.

For added convenience, the Poulan HD1842 comes equipped with an easy-access fuel tank that allows for quick refueling. The mower also features a built-in mulch kit and rear bagger options, making it versatile for different lawn care needs.

In summary, the Poulan HD1842 stands out for its powerful Briggs & Stratton engine, efficient 42-inch cutting deck, advanced hydrostatic transmission, and user-friendly features. This riding lawn mower is designed not only to get the job done efficiently but also to provide comfort and ease of use, making it a fantastic choice for any homeowner looking to maintain a pristine lawn.
Top Page Image Contents