Poulan HD1842 manual Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench

Utility knife

Tire pressure gauge

 

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

INSERT

5/16 HEX BOLT

LOCK WASHER

LARGE FLAT WASHER

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•

Remove all accessible loose parts and parts cartons

 

from carton.

•

Cut along dotted lines on all four panels of carton.

STEERING WHEEL

STEERING BOOT

TABS

Remove end panels and lay side panels flat.

• Check for any additional loose parts or cartons and

remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

ADAPTER

EXTENSION SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment bolt securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents HD1842 Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentReplacing Battery See Figs To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

HD1842 specifications

The Poulan HD1842 is a robust and reliable riding lawn mower designed for homeowners who require efficiency and ease of use while maintaining their lawns. This machine features a powerful engine paired with a 42-inch cutting deck, making it an ideal choice for medium to large-sized yards.

At the heart of the Poulan HD1842 is a reliable 18.5 HP Briggs & Stratton engine, known for its durability and performance. This engine provides ample power to tackle even the toughest grass, ensuring a smooth and effective cutting experience. The engine is designed for easy starting and requires minimal maintenance, making it suitable for users looking for convenience.

One of the standout features of the HD1842 is its cutting deck. The 42-inch deck is equipped with three high-performance blades that provide a clean and even cut, allowing for professional-looking results every time. The deck height can be easily adjusted to six different positions, ranging from 1.5 to 4 inches, giving users the flexibility to choose the perfect height for their grass type and desired look.

Another significant technology integrated into the Poulan HD1842 is the hydrostatic transmission. This feature allows for smooth and effortless speed adjustments while maintaining full control over the mower's movement. Users can easily navigate around obstacles and tight corners without the need to pause and change gears, enhancing the overall mowing experience.

Comfort is also a priority with the HD1842. The mower features a spacious and comfortable seat that can be adjusted to accommodate different user heights. Additionally, the steering wheel is ergonomically designed, providing a better grip and reducing operator fatigue even during extended mowing sessions.

For added convenience, the Poulan HD1842 comes equipped with an easy-access fuel tank that allows for quick refueling. The mower also features a built-in mulch kit and rear bagger options, making it versatile for different lawn care needs.

In summary, the Poulan HD1842 stands out for its powerful Briggs & Stratton engine, efficient 42-inch cutting deck, advanced hydrostatic transmission, and user-friendly features. This riding lawn mower is designed not only to get the job done efficiently but also to provide comfort and ease of use, making it a fantastic choice for any homeowner looking to maintain a pristine lawn.
Top Page Image Contents