Poulan PBGT2254 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

Pliers

(1)

Tire pressure gauge

(1)

9/16" wrench

(1)

Utility knife

(2)

1/2" wrenches

(1)

3/4" wrench

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Remove mower and packing materials.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

•Remove locknut and large flat washer from steering shaft.

•Position front wheels of the tractor so they are pointing straight forward.

•Slide the steering sleeve over the steering shaft.

•Position steering wheel so cross bars are horizontal (left to right) and slide onto steering wheel adapter.

•Secure steering wheel to steering shaft with locknut and large flat washer previously removed. Tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

STEERING WHEEL

INSERT

LOCK NUT

LARGE FLAT WASHER

STEERING WHEEL

STEERING WHEEL ADAP- TOR

STEERING

SHAFT

STEERING

SLEEVE

 

 

 

8

 

 

1

 

8

 

2

 

 

0

 

 

 

FIG. 1

CHECK BATTERY (See Fig. 2)

•Lift hood to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

LABEL

02173

FIG. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model Always Wear EYE Protection During OperationSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation III. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig Assemble Gauge Wheels to Mower Deck SeeInstall Mower and Drive Belt Sees To Attach Nose Roller See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Height Adjustment Knob Used to adjust the mower height Know Your TractorHOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigUsing the Reverse Operation System Reverse Operation System ROSTowing Carts and Other ATTACH- Ments Before Starting the EngineTo Transport Check Engine OIL LevelMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Blade Removal See FigBelts BatteryEngine Transaxle CoolingCleaning To Level Mower Housing Service and AdjustmentsTo Install Mower To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs Mower Drive Belt Removal Mower Drive Belt InstallationTo Replace Mower Drive Belt See Fig Belt RoutingTo Adjust Attachment Clutch See Fig To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbEngine OIL OtherFuel System CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service
Top Page Image Contents