Poulan PC14542B To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 17 and 18)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

BOTTOM EDGE

OF MOWER

OF MOWER

TO GROUND

TO GROUND

“A”

“A”

 

GROUND LINE

FIG. 17

SUSPENSION ARM

LIFT LINK

ADJUSTMENT

NUT

FIG. 18

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length. Both links should be approximately 10-3/8".

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links

an equal number of turns.

20

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 19

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 20

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

MANDREL

IDLER

PULLEY

PULLEYS

 

MANDREL

PULLEY

FIG. 21

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model NO. PC14542B IV. Service Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Steering Wheel SeatKeys Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsADD Gasoline Before Each USE Customer ResponsibilitiesGeneral Recommendations Tractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen To Service PRE-CLEANERTo Service Cartridge Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PC14542BElectrical 2122175141 175158175566 Chassis and Enclosures 176554 17490608Drive 197162 145 120 116 202 150 151174973 7214060873900600 145212Steering Assembly Washer 13/32 x 2-3/8 x 12Ga Engine 170551 148315Seat Assembly Decals Wheels & Tires176396 176851Mower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck 17060514 174493171977 174284Service Notes Limited Warranty Limited Warranties ForSighting Guide CUT This OUT Dotted Is a Slope

PC14542B specifications

The Poulan PC14542B is a reliable and efficient lawn mower designed to tackle your yard maintenance needs with ease. This walk-behind mower features a powerful 14.5-horsepower engine that provides ample power to handle various grass types and terrains. Its 42-inch cutting deck allows for quick mowing over large areas, reducing the time spent on lawn care.

One of the key features of the PC14542B is its ease of use. The mower is equipped with a convenient electric start, ensuring that you can get started without the hassle of pulling a cord multiple times. The automatic choke system helps in achieving optimal engine performance, making it user-friendly, especially for those who may not be familiar with traditional mowers.

The cutting height is adjustable, allowing users to customize their mowing experience based on grass type and desired lawn height. With five position choices, you can effortlessly switch between cutting heights ranging from 1.5 to 4 inches. This versatility is essential for maintaining a healthy and aesthetically pleasing lawn throughout the seasons.

In terms of technology, the Poulan PC14542B features a durable steel deck, which improves the mower’s longevity while also ensuring a clean, even cut. The mower is designed to withstand the rigors of regular use, making it a great investment for homeowners. Additionally, the front washout port makes it easy to clean the cutting deck after use, preventing grass buildup and rust.

Another noteworthy characteristic is its maneuverability. The PC14542B is designed with a tight turning radius, allowing users to navigate easily around flower beds, trees, and other obstacles. The smooth-rolling wheels enhance stability and traction, ensuring that you can mow your lawn comfortably and efficiently.

The Poulan PC14542B also offers additional features, such as a rear bagger for collection, a mulch plug for returning nutrients to the soil, and side discharge capabilities for efficient grass dispersal. This flexibility allows homeowners to choose the most suitable mowing option for their lawn care routine.

In summary, the Poulan PC14542B is an excellent choice for those seeking a durable, efficient, and user-friendly lawn mower. Its powerful engine, versatile cutting heights, and easy maintenance options combine to make yard work less daunting and more enjoyable. Whether you’re maintaining a small yard or a larger property, this mower is equipped to meet various mowing needs effectively.
Top Page Image Contents