Poulan PO18H42STA manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(2)

7/16" wrenches

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten se- curely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

 

INSERT

 

1/2 LOCK WASHER

 

LARGE FLAT

 

WASHER

STEERING

 

WHEEL

 

 

STEERING

 

BOOT

 

TABS

ADAPTER

EXTENSION SHAFT

 

 

1/4 HEX BOLT

1/4 LOCKNUT

 

LOWER

 

STEERING

 

SHAFT

 

 

TAB

 

SLOTS

FIG. 1

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. PO18H42STA General Operation IV. ServiceSafe Operation Practices for Ride-On Mowers II. Slope OperationSafety Rules Table of Contents Key Unassembled PartsSteering Wheel Seat Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Operate on HillsTo Transport See Figs ADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionService Dates MaintenanceLubrication Chart General RecommendationsTractor Engine Muffler CleaningEngine OIL Filter Spark PlugsTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Check BrakeReplacing Battery See Figs Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO18H42STA, Product no 56Tractor - Model Number PO18H42STA, Product no 56 Electrical KEY Part NO. NO. Description Chassis-pl.ltstlt50 KEY Part Description Tractor - Model Number PO18H42STA, Product no 56 Drive Repair Parts 6867 8546 856 KEY Part NO. NO. Description Tractor - Model Number PO18H42STA, Product no 56 Engine Repair Parts KEY Part Description Tractor - Model Number PO18H42STA, Product no 56 Decals Wheels & TiresTractor - Model Number PO18H42STA, Product no 56 Mower Lift Repair Parts Tractor - Model Number PO18H42STA, Product no 56 Mower Deck 165892 Service Notes Service Notes Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

PO18H42STA specifications

The Poulan PO18H42STA is a powerful and versatile lawn tractor designed to make mowing large lawns a breeze. With its robust engine and innovative features, this machine stands out as an exceptional choice for homeowners looking for efficiency and reliability in lawn care.

At the heart of the Poulan PO18H42STA is its 18.5 HP Briggs & Stratton engine, which provides ample power to tackle tough mowing tasks with ease. The engine is known for its durability and performance, ensuring that users can rely on it season after season. Whether you're dealing with thick grass or uneven terrain, the engine's strong output makes it well-suited for a variety of lawn conditions.

A key feature of the PO18H42STA is its 42-inch cutting deck. This deck strikes the perfect balance between maneuverability and cutting width, allowing users to navigate through tight spaces while still covering large areas efficiently. The cutting height can be easily adjusted using a manual lever, offering six different settings for a customized mowing experience tailored to the specific needs of your lawn.

The Poulan PO18H42STA also incorporates a hydrostatic transmission, which provides smooth, precise control over speed and direction. This technology eliminates the need for gear shifting, allowing for seamless operation as you move forward or reverse. It enhances the overall user experience, making it suitable for both seasoned operators and those new to lawn tractors.

For added comfort, this model features a comfortable high-back seat designed to reduce fatigue during longer mowing sessions. The seat is adjustable, allowing users to find their optimal driving position. Additionally, the tractor is equipped with ergonomic controls, making it user-friendly and easy to operate.

In terms of maintenance, the PO18H42STA is designed with accessibility in mind. The engine compartment opens easily for routine checks, and the cutting deck can be removed without hassle for cleaning or blade maintenance. This attention to design simplifies upkeep, ensuring that your lawn tractor remains in top condition.

Overall, the Poulan PO18H42STA is a reliable lawn tractor that combines power, convenience, and comfort. With its strong engine, versatile cutting deck, and user-friendly features, it is an excellent investment for anyone looking to maintain a beautiful lawn with minimal effort. Whether you're mowing grassy expanses or navigating around flower beds, this lawn tractor delivers outstanding performance and versatility.
Top Page Image Contents