Poulan PO175H42STA manual To Check and Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO CHECK AND ADJUST BRAKE (See Fig. 20)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

•Disengage transmission by placing freewhel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress clutch/brake pedal all the way down and en- gage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Engage transmission by placing freewheel control in “transmission engaged” position.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

NUT “A”

1-9/16”

JAM NUT

 

OPERATING

ARM

01513

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUSTMENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SER- VICE CENTER/DEPARTMENT

FIG. 20

TO REPLACE MOTION DRIVE BELT (See Fig. 21)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEYCENTER SPAN KEEPER

FIG. 21

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 22)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model NO. PO175H42STA Safety Rules Safety Rules Table of Contents Steering Wheel Seat Unassembled PartsKey Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Before Starting the EngineTo Transport See Figs To Operate on HillsTo Start Engine See Fig ADD GasolinePurge Transmission Automatic Transmission Warm UPMowing Tips Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine AIR Filter CleaningMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal Transaxle Motion Control Lever Neutral Adjustment See Fig To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

PO175H42STA specifications

The Poulan PO175H42STA is a robust and reliable riding lawn mower designed to provide efficient mowing for homeowners with medium to large-sized lawns. This lawn tractor boasts a variety of features and technologies that enhance its performance, comfort, and ease of use.

One of the standout features of the PO175H42STA is its powerful 17.5 horsepower Briggs & Stratton engine. This reliable engine ensures efficient cutting, even in thicker grass. The engine is designed for easy starting and smooth operation, allowing for a hassle-free mowing experience.

The cutting deck of the Poulan PO175H42STA measures 42 inches, making it ideal for tackling larger areas in a shorter amount of time. The deck's design includes a reinforced frame for added durability, and it offers an adjustable cutting height, allowing users to customize the mowing experience according to their lawn's needs. With six different height settings, ranging from 1.5 inches to 4 inches, users can achieve the perfect cut for their specific grass type and desired look.

The ergonomic design of the Poulan mower also contributes to user comfort. The adjustable high-back seat provides ample support during long mowing sessions, while the soft-touch steering wheel reduces vibrations, enhancing the overall mowing experience. Additionally, the foot-operated deck lift feature allows for seamless adjustments of the cutting height without having to leave the seat, making it highly convenient.

This riding mower is equipped with an automatic transmission, providing a smooth and effortless driving experience. The user-friendly controls make it easy for individuals of all skill levels to operate the mower effectively. The front headlights improve visibility while mowing early in the morning or later in the evening, ensuring that mowing can occur at any time of the day.

In terms of maintenance, the Poulan PO175H42STA includes features that simplify upkeep. The deck wash port makes it easy to clean the underside of the mowing deck, preventing grass clippings from building up and affecting performance. Additionally, its sturdy construction promises longevity, making it a worthwhile investment for those looking to maintain a pristine lawn.

Overall, the Poulan PO175H42STA riding lawn mower combines power, comfort, and user-friendly features, making it a top choice for homeowners who value efficiency and performance in their lawn care routine.
Top Page Image Contents