Poulan PR1742STD owner manual To Adjust Throttle Control Cable See Fig, To Adjust Carburetor

Page 23

SERVICE AND ADJUSTMENTS

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 32)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

GOVERNOR

 

GOVERNOR

CONTROL LEVER

CONTROL

 

 

PLATE

HOLES “A”

CLAMP

THROTTLE

 

SCREW

CABLE

 

 

FIG. 32

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE

GOVERNOR, WHICH IS FACTORY SET FOR PROPER

ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE

T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E

DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED

HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR

N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R /

DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND

E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y

ADJUSTMENTS.

23

Image 23
Contents PR1742STD II. Slope Operation IV. ServiceSafe Operation Practices for Ride-On Mowers General OperationTable of Contents Customer Responsibilities Product SpecificationsContents of Hardware Pack Before Removing Tractor from Skid Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonTo SET UP Your Mower for Mulching Install Seat See FigCheck for Proper Position of ALL Belts To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessLight Battery Reverse Forward FastSee Safety Rules Section Engine on Engine OFF OIL Pressure Lights onKnow Your Tractor HOW to USE Your Tractor Before Starting the Engine Mulching Mowing Tips Mowing TipsTo Start Engine See Fig Before Each USE Lubrication ChartBefore Service Dates General RecommendationsTractor Transaxle Cooling Clean AIR ScreenEngine BeltsEngine OIL Filter CleaningMuffler Spark PlugsTo Remove Mower See Fig To Install Mower See FigFRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigInterlocks and Relays Replacing Battery See FigsTo Remove Hood and Grill Assembly See Fig To Replace Headlight BulbTo Adjust Carburetor To Adjust Throttle Control Cable See FigCylinders OtherFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PR1742STD SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly Adaptor Wheel Strg Seat Assembly Wheels and Tires DecalsEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift Tractor Model Number PR1742STD159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policywarranty Guide Only Ride UP and Down HillSighting Not Across HillParts and Service