Poulan PPR20H42STA Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 17

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 12)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer secur- ing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

TRAILING

MANDREL

ASSEMBLY

EDGE UP

 

BLADE

 

 

CENTER

 

HOLE

LOCK WASHER

STAR

FLAT WASHER

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 12

TO SHARPEN BLADE (See Fig. 13)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 13

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents PPR20H42STA IV. Service Safety RulesGeneral Operation II. Slope OperationSafety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingCheck Deck Levelness To Convert to Bagging or DischargingOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other Attach Before Starting the EngineMents Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsPurge Transmission Mulching Mowing Tips Everybefore Service Dates Lubrication ChartCustomer Responsibilities General RecommendationsBrake Operation TractorTires Operator Presence SystemEngine Clean AIR INTAKE/COOLING Areas Clean AIR ScreenCleaning MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Installation To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Attach Jumper CablesTo Replace Fuse To Adjust CarburetorInterlocks and Relays Other StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PPR20H42STA SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsSpark Arrester EngineOptional Equipment 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PPR20H42STA specifications

The Poulan PPR20H42STA is a powerful and versatile riding lawn mower designed to tackle a variety of mowing tasks efficiently. This model combines user-friendly features with advanced technology, making it an ideal choice for homeowners with medium to large lawns. One prominent feature of the PPR20H42STA is its robust 20 HP Briggs & Stratton engine, which provides ample power to handle thick grass and uneven terrain. The engine is designed for easy starting and minimal maintenance, ensuring that users can quickly get back to mowing without the hassle of complicated upkeep.

One of the standout characteristics of the Poulan PPR20H42STA is its 42-inch cutting deck. This size strikes a perfect balance between maneuverability and coverage, allowing the mower to navigate tight spaces while efficiently cutting a larger area in fewer passes. The deck's dual blades promote a clean and even cut, contributing to a healthier lawn. Additionally, the deck height is adjustable, offering six different cutting positions to customize the mowing height according to your preferences and grass type.

The PPR20H42STA features a hydrostatic transmission, providing smooth and seamless speed control. This technology allows users to easily change speeds without the hassle of shifting gears, resulting in a more enjoyable mowing experience. The mower's tight turning radius enhances maneuverability, making it easier to trim around flower beds and trees.

Comfort has also been prioritized in the design of the Poulan PPR20H42STA. An ergonomic, high back seat provides ample support during prolonged use, reducing fatigue. The steering wheel and control levers are positioned for easy access, enabling users to operate the mower with minimal effort.

For added convenience, the Poulan PPR20H42STA includes a built-in storage compartment for tools and small items, ensuring that everything needed for lawn care is within easy reach. The mower also showcases a rugged and durable construction, with a strong chassis built to withstand tough conditions.

Overall, the Poulan PPR20H42STA defines reliability and efficiency in lawn care. Its powerful engine, superior cutting capabilities, and user-friendly design make it a valuable addition to any homeowner's landscaping toolkit. Whether you’re mowing grass or navigating uneven terrain, this mower is designed to deliver outstanding performance every time.
Top Page Image Contents