Poulan PPR20H42STC Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel Alignment

Page 23

SERVICE AND ADJUSTMENTS

ENGINE

PULLEY

CLUTCHING

IDLER

STATION-

ARY IDLER

TRANSMISSION

 

INPUT PULLEY

CENTER SPAN

 

KEEPER

FIG. 25

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMIS- SION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been preset at the factory and adjustment should not be necessary.

Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

Start engine and move motion control lever until tractor does not move forward or backward.

Hold motion control lever in that position and turn engine off.

While holding motion control lever in place, loosen the adjustment bolt.

Move motion control lever to the neutral (N) (lock gate) position.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

Loosen the adjustment bolt.

Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL

NEUTRAL

LOCK GATE

LEVER

 

 

ADJUSTMENT

 

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 27

23

Image 23
Contents PPR20H42STC II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other Attach MentsAutomatic Transmission Warm UP Mowing TipsPurge Transmission Mulching Mowing Tips General Recommendations Lubrication ChartService Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresEngine Muffler Clean AIR ScreenClean AIR INTAKE/COOLING Areas CleaningTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbTo Replace Fuse To Adjust CarburetorInterlocks and Relays Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PPR20H42STC SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly 180656 Wheel Steering KEY Part NO. NO. Description Seat AssemblyWheels and Tires DecalsSpark Arrester EngineOptional Equipment 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PPR20H42STC specifications

The Poulan PPR20H42STC is a versatile and powerful garden tool designed for homeowners seeking an efficient solution for maintaining their lawns and gardens. This riding lawn mower stands out for its balance of performance, durability, and user-friendly features, making it an excellent choice for various mowing tasks.

One of the primary features of the PPR20H42STC is its robust 20-horsepower engine. This powerful engine ensures that you can tackle even the toughest grass and terrain without compromising on performance. The mower's engine is designed for longevity and reliability, providing the strength needed to handle extensive mowing jobs with ease.

The PPR20H42STC comes equipped with a 42-inch cutting deck. This mid-sized deck offers a perfect compromise between maneuverability and coverage, allowing users to navigate through tighter spaces while still covering larger areas efficiently. The cutting deck features adjustable heights, enabling homeowners to choose the ideal grass length for their lawns, ensuring a well-manicured appearance.

In terms of technology, the Poulan PPR20H42STC incorporates a hydrostatic transmission system. This transmission delivers smooth acceleration and deceleration, eliminating the need for shifting gears. As a result, users can experience a more relaxed mowing experience, focusing entirely on the task at hand without the distractions of a complicated gear system.

Another notable characteristic of this riding mower is its comfort-focused design. The PPR20H42STC features an ergonomic seat with plenty of cushioning, providing comfort during extended mowing sessions. The steering wheel's design allows for easy maneuverability, further enhancing the user experience.

The mower's rugged construction includes a durable frame and high-quality materials, ensuring it can withstand the rigors of outdoor use. Additionally, maintenance is simplified with easily accessible components, enabling homeowners to perform regular upkeep with minimal effort.

Safety is also a priority within the PPR20H42STC design. The mower is fitted with features such as an operator presence system that prevents accidental starts when the operator is not seated, enhancing overall user safety.

In conclusion, the Poulan PPR20H42STC is an impressive riding lawn mower that combines power, comfort, and safety features to create a reliable tool for lawn maintenance. With its strong engine, versatile cutting deck, and thoughtful design, it's an excellent investment for homeowners aiming for a pristine lawn.