Poulan PPR20H42STC owner manual Install Seat See Fig

Page 7

ASSEMBLY

SEAT PAN

LABEL

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section, page 10, for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in freewheeling position to disengage transmission (See “TO TRANSPORT” in the Operation section of this manual).

FIG. 2

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Roll tractor forward off skid.

•Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Opera- tion section, page 10, for location and func- tion of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been completed.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" po- sition.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

• Get off seat without moving its adjusted position.

•

Place motion control lever in neutral (N) position.

• Raise seat and tighten adjustment knob securely.

•

Press lift lever plunger and raise attachment lift lever to

 

 

its highest position.

 

• Start the engine. After engine has started, move throttle

SEAT

 

control to idle position.

•

Release parking brake.

 

 

• Slowly move the motion control lever forward and slowly

 

 

drive tractor off skid.

 

• Apply brake to stop tractor, set parking brake and place

SEAT PAN

 

motion control lever in neutral position.

• Turn ignition key to "OFF" position.

 

 

Continue with the instructions that follow.

SHOULDER

 

 

BOLT

 

 

FLAT WASHER

 

 

ADJUSTMENT

 

 

KNOB

 

 

FIG. 3

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents PPR20H42STC II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other Attach MentsPurge Transmission Mowing TipsAutomatic Transmission Warm UP Mulching Mowing Tips General Recommendations Lubrication ChartService Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresEngine Muffler Clean AIR ScreenClean AIR INTAKE/COOLING Areas CleaningTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbInterlocks and Relays To Adjust CarburetorTo Replace Fuse Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PPR20H42STC SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly 180656 Wheel Steering KEY Part NO. NO. Description Seat AssemblyWheels and Tires DecalsOptional Equipment EngineSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PPR20H42STC specifications

The Poulan PPR20H42STC is a versatile and powerful garden tool designed for homeowners seeking an efficient solution for maintaining their lawns and gardens. This riding lawn mower stands out for its balance of performance, durability, and user-friendly features, making it an excellent choice for various mowing tasks.

One of the primary features of the PPR20H42STC is its robust 20-horsepower engine. This powerful engine ensures that you can tackle even the toughest grass and terrain without compromising on performance. The mower's engine is designed for longevity and reliability, providing the strength needed to handle extensive mowing jobs with ease.

The PPR20H42STC comes equipped with a 42-inch cutting deck. This mid-sized deck offers a perfect compromise between maneuverability and coverage, allowing users to navigate through tighter spaces while still covering larger areas efficiently. The cutting deck features adjustable heights, enabling homeowners to choose the ideal grass length for their lawns, ensuring a well-manicured appearance.

In terms of technology, the Poulan PPR20H42STC incorporates a hydrostatic transmission system. This transmission delivers smooth acceleration and deceleration, eliminating the need for shifting gears. As a result, users can experience a more relaxed mowing experience, focusing entirely on the task at hand without the distractions of a complicated gear system.

Another notable characteristic of this riding mower is its comfort-focused design. The PPR20H42STC features an ergonomic seat with plenty of cushioning, providing comfort during extended mowing sessions. The steering wheel's design allows for easy maneuverability, further enhancing the user experience.

The mower's rugged construction includes a durable frame and high-quality materials, ensuring it can withstand the rigors of outdoor use. Additionally, maintenance is simplified with easily accessible components, enabling homeowners to perform regular upkeep with minimal effort.

Safety is also a priority within the PPR20H42STC design. The mower is fitted with features such as an operator presence system that prevents accidental starts when the operator is not seated, enhancing overall user safety.

In conclusion, the Poulan PPR20H42STC is an impressive riding lawn mower that combines power, comfort, and safety features to create a reliable tool for lawn maintenance. With its strong engine, versatile cutting deck, and thoughtful design, it's an excellent investment for homeowners aiming for a pristine lawn.
Top Page Image Contents