Poulan PO14542F manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

FIG. 26

KEPS

NUT

HEX

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

FIG. 27

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 28)

• Raise hood.

• Unsnap headlight wire connector.

• Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

• To replace, reverse above procedure.

23

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 28

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 29)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

GOVERNOR

 

GOVERNOR

CONTROL LEVER

 

 

CONTROL PLATE

 

 

HOLES “A”

CLAMP

THROTTLE

 

 

SCREW

 

CABLE

 

 

FIG. 29

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. PO14542F II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Slope Sheet Unassembled PartsSteering Wheel Seat KeysTo Remove Tractor from CAR- TON AssemblyTools Required for Assembly HOW to SET UP Your TractorLower seat into operating position and sit on seat Install Seat See FigCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To TransportTo Start Engine See Fig Mowing TipsADD Gasoline General Recommendations Lubrication ChartService Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsEngine Cooling Fins See Fig Clean AIR ScreenTo Service PRE-CLEANER To Service CartridgeIN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigTo Attach Jumper Cables To Adjust Steering Wheel AlignmentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWhen operator leaves Tractor Model Number PO14542F, Product Number 954 56 Schematic4529 ElectricalKEY Part Description Chassis and Enclosures Repair Parts Drive 72110614 Steering Assembly KEY Part NO. NO. Description Engine KEY Part Description Seat Assembly Wheels & Tires DecalsMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck 72110505 Service Notes Limited Warranty C U M SEH Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

PO14542F specifications

The Poulan PO14542F is a versatile and efficient lawn mower that stands out in the crowded market of residential lawn care equipment. Designed for both ease of use and effective performance, it is an ideal choice for homeowners looking to maintain a well-groomed lawn without the hassle of complicated machinery.

One of the main features of the Poulan PO14542F is its powerful 14.5 horsepower engine, providing ample strength to tackle various types of grass and uneven terrains. The engine is coupled with a 42-inch cutting deck, which allows for a wider cutting path, ensuring that users can cover more ground with fewer passes. This efficiency is particularly valuable for maintaining larger lawns.

The mower is designed with a hydrostatic transmission, offering smooth and effortless adjustments to speed. This technology makes it easier for users to navigate their lawns, enabling them to slow down or speed up as required without the need to switch gears manually. This feature enhances the overall riding experience, allowing for a more relaxed mowing session.

Another notable characteristic of the Poulan PO14542F is its cutting height adjustment feature. The mower provides multiple height settings, allowing users to customize the length of their grass according to their preferences. Whether you want a close trim or a longer cut, the mower caters to various cutting needs with ease.

User comfort is also a priority in the design of the Poulan PO14542F. The machine features an ergonomic seat with a high back, providing substantial support during long mowing sessions. Additionally, it incorporates easy-to-reach controls, making adjustments simple while driving.

In terms of durability, the Poulan PO14542F is built with a robust steel frame and deck, ensuring longevity and resilience against the elements. Its rugged tires provide excellent traction, making it suitable for various terrains, including slopes and uneven ground.

Overall, the Poulan PO14542F is a reliable and efficient lawn mower that combines power, comfort, and convenience. Its prominent features, such as the hydrostatic transmission, adjustable cutting heights, and durable construction, make it a worthy investment for any homeowner looking to enhance their lawn care routine. With this mower, keeping your lawn pristine becomes a straightforward and enjoyable task.
Top Page Image Contents