Poulan PDB18H42STA To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

Remove retainer spring and clevis pin which secure each gauge wheel bar.

Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

Replace retainer spring into clevis pin.

Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS

PIN

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

Select desired height of cut.

Lower mower with attachment lift control.

Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT LIFT LEVER HIGH POSITION

ATTACHMENT

 

CLUTCH LEVER

LOW

"DISENGAGED"

POSITION

POSITION

 

DEFLECTOR

SHIELD

FIG. 8

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

Choose the slowest speed before starting up or down hills.

Avoid stopping or changing speed on hills.

If slowing is necessary, move throttle control lever to slower position.

If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED.

To restart movement, slowly release parking brake and clutch/brake pedal.

Slowly move motion control lever to slowest setting.

Make all turns slowly.

TO TRANSPORT (See Figs. 5 and 9)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

Raise attachment lift to highest position with attachment lift control.

Pull freewheel control out and into the slot and release so it is held in the disengaged position.

Do not push or tow tractor at more than two (2) MPH.

To reengage transmission, reverse above procedure.

12

Image 12
Contents PDB18H42STA Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel SeatGauge Wheel Slope SheetAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See aTo SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Mulching Mowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning Engine OIL FilterMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PDB18H42STATractor - Model Number PDB18H42STA Electrical KEY Part NO. NO. Description Tractor - Model Number PDB18H42STA Chassis and Enclosures KEY Part Description Tractor - Model Number PDB18H42STA Drive Repair Parts Tractor - Model Number PDB18H42STA Steering Assembly 180656 Wheel Steering Tractor - Model Number PDB18H42STA Engine KEY Part NO. NO. Description Tractor - Model Number PDB18H42STA Seat Assembly Tractor - Model Number PDB18H42STA Decals Wheels & TiresTractor - Model Number PDB18H42STA Mower Lift Repair Parts Tractor - Model Number PDB18H42STA Mower Deck 182032X421 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service