Poulan PKGTH2554 To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 13

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 10)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

019

77

 

CLEVIS

PIN

FIG. 10

TO OPERATE MOWER (See Fig. 11)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

13

 

 

LIFT LEVER

 

 

HIGHEST

 

 

POSIITON

 

 

LOWEST

 

 

POSITION

ATTACHEMNT

 

 

CLUTCH

 

 

SWITCH PULL

 

 

OUT TO

 

 

"ENGAGE"

 

 

PUSH IN TO

 

 

"DISENGAGE"

02142

DEFLECTOR

 

 

 

 

 

SHIELD

FIG. 11

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

•Move motion control lever to neutral (N) position.

•With engine running, turn ignition key counterclockwise to ROS "ON" position.

•Look down and behind before backing.

•Slowly move motion control lever to reverse (R) position to start movement.

•When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

02828

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Always Wear EYE Protection During Operation ModelGeneral Operation Safe Operation Practices for Ride-On MowersII. Slope Operation General Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt SeesCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Height Adjustment Knob Used to adjust the mower heightHOW to USE Your Tractor Using the Reverse Operation System To Adjust Gauge Wheels See FigTo Operate Mower See Fig Reverse Operation System ROSTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Install Mower Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs To Replace Mower Drive Belt See Fig Mower Drive Belt InstallationMower Drive Belt Removal Belt RoutingTo Check and Adjust Brake To Adjust Attachment Clutch See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight Bulb Interlocks and RelaysFuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PKGTH2554 specifications

The Poulan PKGTH2554 is a robust and versatile lawn tractor designed to meet the needs of homeowners who desire a reliable machine for maintaining their lawns. Known for its strong performance and a range of useful features, this tractor stands out in the crowded market of residential lawn care equipment.

At the heart of the PKGTH2554 is its powerful 25 HP Kohler engine, which provides ample power to tackle various tasks with ease, whether it’s mowing, bagging, or towing attachments. The engine is equipped with a reliable starter system, ensuring that it fires up quickly and efficiently, making it perfect for both quick lawn care sessions and extended use.

One of the standout features of the PKGTH2554 is its 54-inch cutting deck. This wide deck allows for efficient mowing, covering a larger area in fewer passes, which saves time when maintaining larger lawns. The deck height can be easily adjusted using a lever, giving users the flexibility to choose the perfect cutting height for their lawn's specific needs. This versatility ensures that grass is cut to the desired length, promoting a healthier lawn.

The tractor also boasts a hydrostatic transmission, which enhances maneuverability and ease of use. Unlike traditional gear-driven systems, hydrostatic transmissions allow for smooth and seamless speed adjustments with a simple push of the pedal. This feature is particularly beneficial when navigating around obstacles or working in tight spaces.

In terms of comfort, the PKGTH2554 is equipped with a plush, high-back seat that provides ample support during extended mowing sessions. The user-friendly controls and ergonomic layout of the operator station enhance the overall experience, making it easy for anyone to operate.

For added capability, the PKGTH2554 comes with the option to attach various accessories, including baggers, plows, and other lawn care implements. This adaptability allows homeowners to customize their tractor according to their specific needs and seasonal requirements.

Overall, the Poulan PKGTH2554 delivers a perfect combination of power, versatility, and comfort. With its efficient cutting capabilities, adaptable features, and user-friendly design, it is an excellent choice for homeowners looking to simplify lawn maintenance while achieving professional results.
Top Page Image Contents