Poulan AG17542STB manual To Replace Motion Drive Belt, To Adjust Steering Wheel ALIGN- Ment

Page 24

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1.Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2.Remove belt from stationary idler and clutching idler.

3.Remove belt downward from around engine pulley.

4.Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keepers.

5.Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

1.Carefully work new belt down between transaxle belt keepers and onto the input pulley.

2.Slide belt into the center span keeper.

3.Pull belt toward front of tractor and roll around the top groove of engine pulley.

4.Install belt through stationary idler and clutching idler.

5.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

6.Install mower (See “TO INSTALL MOWER” in this section of manual).

Engine

Pulley

Clutching

Idler

Stationary

Idler

Center

Span

Keeper

Transaxle

Pulley

00811

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

Washers

Retaining

Ring

Axle

Cover

Square Key

(Rear Wheel Only)

24

Image 24
Contents Model NO. AG17542STB Table of Contents WarrantySafety Rules General OperationII. Slope Operation IV. Service III. ChildrenDo not Safety Rules Product Specifications Customer ResponsibilitiesAPI-SG-SL Unassembled Parts Tools Required for Assembly HOW to SET UP Your TractorTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery Check Tire Pressure Check for Proper Position of ALL BeltsCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower To Operate on HillsBefore Starting the Engine To Start EngineMowing Tips Maintenance General Recommendations Lubrication ChartBefore Each USE Tractor Battery EngineTransaxle Cooling BeltsCleaning Service and Adjustments To Install MowerTo Remove Mower To Level Mower Housing SIDE-TO-SIDE AdjustmentTo Check and Adjust Brake To Replace Mower Blade Drive BeltTo Adjust Steering Wheel ALIGN- Ment To Replace Motion Drive BeltFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Start Engine with a Weak Battery Replacing BatteryTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Carburetor To Adjust Throttle Control CableInterlocks and Relays To Replace FuseBattery OtherFuel System Engine OILTroubleshooting Chart Problem Cause CorrectionExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation