Poulan 960120003 manual Tractor, Blade Removal See Fig, To Sharpen Blade See Fig

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than fi ve (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See“PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without fi rst setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

828

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 8)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and fl at washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS HEATTREATED.IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN IN THE REPAIR PARTS.

 

 

MANDREL

TRAILING

BLADE

ASSEMBLY

EDGE UP

 

 

CENTER

 

 

 

 

HOLE

FLAT WASHER

 

 

LOCK WASHER

 

STAR

BLADE BOLT

FIG. 8

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a fi le or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PB18542LT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Reverse Operation System ROSTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance Maintenance ScheduleLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Battery EngineBelts Transaxle CoolingCleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

960120003 specifications

The Poulan 960120003 is a robust and reliable lawn mower renowned for its efficiency and ease of use, making it an excellent choice for homeowners and landscaping professionals alike. One of its standout features is its powerful engine, which typically includes a 163cc Briggs & Stratton single-cylinder engine. This engine provides ample power to tackle even the most demanding mowing tasks, ensuring a clean and even cut every time.

Equipped with a 21-inch cutting deck, the Poulan 960120003 offers a substantial cutting width that allows for efficient mowing of medium to large-sized yards. The adjustable cutting height feature is another significant advantage, enabling users to customize the deck height to suit different types of grass and seasonal conditions, typically ranging from 1 to 3.5 inches.

In terms of technology, the Poulan 960120003 incorporates advanced features designed to enhance user control and comfort. The mower employs a self-propelling mechanism that allows the user to navigate through varying terrains with ease, reducing physical exertion and making the mowing experience more enjoyable. This system typically operates at variable speeds, giving the operator the flexibility to adjust the speed according to their comfort and the nature of the lawn.

Another noteworthy characteristic of the Poulan 960120003 is its ease of maintenance. The mower is designed for quick and straightforward maintenance procedures, including easier access to the air filter and spark plug, allowing the owner to perform routine checks without professional assistance. The 21-inch steel chassis also offers durability, ensuring longevity and resilience against the rigors of regular lawn care.

Additionally, the Poulan 960120003 features a foldable handle for convenient storage, making it easy to stow away in a garage or shed when not in use. The robust design, combined with lightweight construction, ensures that the mower is not only powerful but also easy to maneuver even in tight spaces.

Overall, the Poulan 960120003 stands out in the competitive lawn care market due to its combination of power, efficiency, and innovative features. Its thoughtful design and dependable performance make it a practical choice for anyone looking to maintain their lawn effectively and efficiently. Whether it's a simple weekly trim or a larger landscaping project, this mower is equipped to handle a variety of lawn care tasks with ease.
Top Page Image Contents