Poulan 960120003 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench

Utility knife

(2) 3/4" wrench

Tire pressure gauge

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels fl at.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large fl at washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK

WASHER

LARGE FLAT

WASHER

STEERING

WHEEL

STEERING

BOOT

TABS

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and fl at washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and fl at washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PB18542LT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Operate Mower See FigReverse Operation System ROS To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Lubrication Chart MaintenanceMaintenance Schedule General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingCleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

960120003 specifications

The Poulan 960120003 is a robust and reliable lawn mower renowned for its efficiency and ease of use, making it an excellent choice for homeowners and landscaping professionals alike. One of its standout features is its powerful engine, which typically includes a 163cc Briggs & Stratton single-cylinder engine. This engine provides ample power to tackle even the most demanding mowing tasks, ensuring a clean and even cut every time.

Equipped with a 21-inch cutting deck, the Poulan 960120003 offers a substantial cutting width that allows for efficient mowing of medium to large-sized yards. The adjustable cutting height feature is another significant advantage, enabling users to customize the deck height to suit different types of grass and seasonal conditions, typically ranging from 1 to 3.5 inches.

In terms of technology, the Poulan 960120003 incorporates advanced features designed to enhance user control and comfort. The mower employs a self-propelling mechanism that allows the user to navigate through varying terrains with ease, reducing physical exertion and making the mowing experience more enjoyable. This system typically operates at variable speeds, giving the operator the flexibility to adjust the speed according to their comfort and the nature of the lawn.

Another noteworthy characteristic of the Poulan 960120003 is its ease of maintenance. The mower is designed for quick and straightforward maintenance procedures, including easier access to the air filter and spark plug, allowing the owner to perform routine checks without professional assistance. The 21-inch steel chassis also offers durability, ensuring longevity and resilience against the rigors of regular lawn care.

Additionally, the Poulan 960120003 features a foldable handle for convenient storage, making it easy to stow away in a garage or shed when not in use. The robust design, combined with lightweight construction, ensures that the mower is not only powerful but also easy to maneuver even in tight spaces.

Overall, the Poulan 960120003 stands out in the competitive lawn care market due to its combination of power, efficiency, and innovative features. Its thoughtful design and dependable performance make it a practical choice for anyone looking to maintain their lawn effectively and efficiently. Whether it's a simple weekly trim or a larger landscaping project, this mower is equipped to handle a variety of lawn care tasks with ease.
Top Page Image Contents