Poulan 402559 manual Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place motion control lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 15)

Mower will be easier to remove from the right side of trac- tor.

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Remove small retainer spring, and remove clutch spring off pulley bolt.

•Remove large retainer spring, slide collar off and push housing guide out of bracket.

•Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHERTHANTHE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONTLINKSANDHOOKTHECLUTCHSPRINGINTOSQUARE HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 15)

•Raise attachment lift lever to its highest position.

•Slide mower under tractor with defl ector shield to right side of tractor.

•Lower lift lever to its lowest position.

•Connect front links to mower deck and secure with retainer springs..

•Connect suspension arms to rear deck brackets and secure with retainer springs.

•Connect anti-swaybar to chassis bracket and secure with retainer spring.

•Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

•Place fl at washer and clutch spring on idler pulley bolt and secure with small retainer spring.

•Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly infl ated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinfl ated, you will not properly adjust your mower.

 

SMALL RETAINER SPRING

 

 

 

 

CLUTCH SPRING

 

 

 

 

FLAT WASHER

 

 

SQUARE HOLE

SMALL RETAINER SPRING

 

SUSPENSION

ENGINE PULLEY

 

 

 

ARMS

 

 

 

 

CLUTCH SPRING

 

 

 

 

 

 

 

FRONT LINK

RETAINER SPRING

 

 

 

 

ANTI-SWAY BAR

 

 

 

 

 

 

 

 

RETAINER SPRINGS

COLLAR

 

 

 

(BOTH SIDES)

HOUSING GUIDE

LARGE RETAINER

 

 

 

SPRING

BRACKET

 

DEFLECTOR SHIELD

 

 

 

 

 

 

 

FIG. 15

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Always Wear EYE Protection During Operation PB19H42LTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System To Operate Mower See FigADD Gasoline Before Starting the EngineTo Transport See Figs Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP Before Each USE MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust BrakeFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

402559, 96012004701 specifications

The Poulan 96012004701 and 402559 are innovative outdoor power equipment tools designed for both professional landscapers and avid gardeners. These tools are crafted with advanced technologies and features that enhance performance, reliability, and ease of use.

One of the standout features of these Poulan products is their powerful engine performance. Both models typically come equipped with robust two-cycle engines that deliver reliable power with efficient fuel consumption. This means that users can tackle a variety of outdoor tasks without the worry of frequent refueling or interruptions. The engines are designed to be lightweight, reducing user fatigue during prolonged usage.

Durability is another hallmark of the Poulan 96012004701 and 402559 models. Constructed with high-quality materials, these tools can withstand the rigors of outdoor environments. Whether cutting through thick brush or trimming delicate hedges, users can rely on the sturdy build to handle various applications. Additionally, the components are often resistant to wear and tear, ensuring longevity and consistent performance.

User comfort and ergonomics are central to the design of these models. They are typically equipped with adjustable handles that provide a customized grip, allowing for comfort during extended use. The anti-vibration technology integrated into the handle helps to reduce fatigue and strain on the arms and hands, making each job more manageable.

In terms of versatility, the Poulan 96012004701 and 402559 are designed to tackle a wide range of outdoor tasks. Whether it’s edging a garden bed, trimming overgrown areas, or maintaining a manicured lawn, these tools are adaptable to the demands of the job. The ease of blade or attachment changes allows users to switch tasks swiftly, making these models efficient and time-saving.

Safety features also play an essential role in the design of these Poulan products. They commonly include features like protective guards and easy-start technologies, aimed at minimizing the risks associated with outdoor power equipment. The user-friendly starting mechanisms reduce the chances of accidental starts, providing peace of mind while operating.

In conclusion, the Poulan 96012004701 and 402559 combine power, durability, and user-centric design, making them reliable choices for anyone looking to enhance their landscaping capabilities. Whether for home use or professional landscaping services, these models stand out for their efficiency and performance, ensuring that outdoor tasks are completed with ease and precision.
Top Page Image Contents